manualshive.com logo in svg

Texas Instruments OMAP5910, Technical Reference Manual

The Texas Instruments OMAP5910 is an advanced electronic device, offering exceptional functionalities and high performance. To make the most out of this product, it is advisable to refer to the comprehensive "Reference Manual" available for download, free of charge, from our website.

Share
Download
background image

UART/Autobaud Control and Status Registers

12-17

UART Devices

12.3 UART/Autobaud Control and Status Registers

The programming combinations for register selection are shown in
Table 12–12.

12.3.1 UART/Autobaud Modem Register Mapping

UART1 and UART2 are accessible as follows:

-

MPU (32-bit-byte aligned address) from the following base addresses:

J

UART1: 0xFFFB 0000

J

UART2: 0xFFFB 0800

-

DSP (16-bit-aligned word address) from the following base addresses:

J

UART1: 0x008000

J

UART2: 0x008400

Table 12–12. UART Modem Register Program  

Registers

MPU

Byte

Off-

DSP

Byte

Off-

LCR[7] = 0

LCR[7] = 1

LCR[7:0] 

≠

 0xBF

LCR[7:0] = 0xBF

Off-

set

Off-

set

READ

WRITE

READ

WRITE

READ

WRITE

0x00

0x00

RHR

THR

DLL

DLL

DLL

DLL

0x04

0x02

IER

†

IER

†

DLH

DLH

DLH

DLH

0x08

0x04

IIR

FCR

†

IIR

FCR

†

EFR

EFR

0x0C

0x06

LCR

LCR

LCR

LCR

LCR

LCR

0x10

0x08

MCR

†

MCR

†

MCR

†

MCR

†

XON1

XON1

0x14

0x0A

LSR

-

LSR

-

XON2

XON2

0x18

0x0C

MSR/TCR

‡

TCR

‡

MSR/TCR

‡

TCR

‡

XOFF1/TCR

‡

XOFF1/TCR

‡

0x1C

0x0E

SPR/TLR

‡

SPR/TLR

‡

SPR/TLR

‡

SPR/TLR

‡

XOFF2/TLR

‡

XOFF2/TLR

‡

0x20

0x10

MDR1

MDR1

MDR1

MDR1

MDR1

MDR1

0x24

0x12

-

-

-

-

-

-

0x28

0x14

-

-

-

-

-

-

0x2C

0x16

-

-

-

-

-

-

† MCR[7:5], FCR[5:4], and IER[7:4] can only be written when EFR[4] = 1.
‡ Transmission control register (TCR) and trigger level register (TLR) are accessible only when EFR[4] = 1 and MCR[6] = 1.

Summary of Contents for OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP5910

Campbell NL115 Instruction Manual preview
NL115
Brand: Campbell Pages: 42
SMART MOD IIC Installation And Service Manual preview
MOD IIC
Brand: SMART Pages: 15
Broadcom Brocade X6-8 Director Hardware Installation Manual preview
Brocade X6-8 Director
Brand: Broadcom Pages: 207
Valcom VIP-822A Quick Start Manual preview
VIP-822A
Brand: Valcom Pages: 4
Avenview DVI-PROWALL-9X Instruction Manual preview
DVI-PROWALL-9X
Brand: Avenview Pages: 28
Loopcomm LP-8014 Quick Start Manual preview
LP-8014
Brand: Loopcomm Pages: 2
ICP Chapter C Quick Setup Manual preview
Chapter C
Brand: ICP Pages: 68
LevelOne FSW-0808TX Quick Start Manual preview
FSW-0808TX
Brand: LevelOne Pages: 3
IEI Technology Mustang-M2AE-MX1 User Manual preview
Mustang-M2AE-MX1
Brand: IEI Technology Pages: 58
Crest Audio NC-MCO - TECHNICAL Technical Data preview
NC-MCO - TECHNICAL
Brand: Crest Audio Pages: 2
Avigilon NVR5-STD-10GBE Installation Manual preview
NVR5-STD-10GBE
Brand: Avigilon Pages: 12
XtendLan XL-VC102SB User Manual preview
XL-VC102SB
Brand: XtendLan Pages: 17
CSI 7798 I/SITE LAN Installation Manual preview
7798 I/SITE LAN
Brand: CSI Pages: 56
Grundfos CIM 060 Installation And Operating Instructions Manual preview
CIM 060
Brand: Grundfos Pages: 40
LanReady AP-952X User Manual preview
AP-952X
Brand: LanReady Pages: 40
IBM 09N4076 User Manual preview
09N4076
Brand: IBM Pages: 78
Siklu EtherHaul 500 Installation Manual preview
EtherHaul 500
Brand: Siklu Pages: 52
8e6 Technologies Threat Analysis Reporter TAR HL/SL/MSA Evaluation Manual preview
Threat Analysis Reporter TAR HL/SL/MSA
Brand: 8e6 Technologies Pages: 22

Brands by name

Popular brands

Load more brands