manualshive.com logo in svg

Texas Instruments OMAP5910, Technical Reference Manual

The Texas Instruments OMAP5910 is an advanced electronic device, offering exceptional functionalities and high performance. To make the most out of this product, it is advisable to refer to the comprehensive "Reference Manual" available for download, free of charge, from our website.

Share
Download
background image

Registers

5-53

System DMA Controller

Table 5–23. DMA Channel Element Index Register (DMA_CEI)

Bit

Name

Description

Type

Reset

Value

15–0

Element index

Contains the element index, expressed in bytes, used to
compute the addresses when single-index addressing
mode is used.

RW

Undefined

Table 5–24. DMA Channel Progress Counter Register (DMA_CPC)

Bit

Name

Description

Type

Reset

Value

15–0

Last element/
frame address
16 LSB

This register can be used to monitor the progress of a
DMA transfer:

-

If the channel transfer is synchronized on elements
(DMA_CCR SYNC 

≠ 

0 and DMA_CCR FS = 0), the

register is updated with the address 16 LSB each time
the destination port issues the last request for an
element.

-

If the channel transfer is synchronized on frames
(DMA_CCR SYNC 

≠ 

0 and DMA_CCR FS = 1) or not

synchronized (DMA_CCR SYNC = 0), the register is
updated with 16 LSB of the address each time the
destination port issues the last request for a frame.

R

Undefined

The DMA LCD control register contains seven bits that control the LCD chan-
nel operation. There are two cases of interruption: end frame buffer or abort
on the bus (bus error). Bit IE (interrupt enable) enables the generation of the
interruption.

If the COND bit and the corresponding IE bit are set, an interrupt signal is sent
from the DMA channel to the MPU. The MPU reads this register to find the
cause of the interruption.

-

COND = 0: Condition not detected

-

COND = 1: Condition detected

The COND bit is updated during a transfer, and the host processor must reset
this bit after reading.

Summary of Contents for OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP5910

Acconeer A111 User Manual preview
A111
Brand: Acconeer Pages: 32
ETAS FETK-S2.1 User Manual preview
FETK-S2.1
Brand: ETAS Pages: 69
Lucent Technologies PARTNER Voice Messaging PC Card Release 2 Installation And Programming preview
PARTNER Voice Messaging PC Card Release 2
Brand: Lucent Technologies Pages: 67
Direct IP IDIS DR-1304P Operation Manual preview
IDIS DR-1304P
Brand: Direct IP Pages: 76
Phytec L-843e.A1 Hardware Manual preview
L-843e.A1
Brand: Phytec Pages: 53
ZyXEL Communications EOC350 Series Quick Start Manual preview
EOC350 Series
Brand: ZyXEL Communications Pages: 2
Dahua NVS0X04DH Quick Start Manual preview
NVS0X04DH
Brand: Dahua Pages: 24
WHOOP WHT-25LT Quick Start Manual preview
WHT-25LT
Brand: WHOOP Pages: 26
Fracarro FRPRO EVO HD Quick Start Manual preview
FRPRO EVO HD
Brand: Fracarro Pages: 12
Multitech MultiConnect SE MTS2EA Specification Sheet preview
MultiConnect SE MTS2EA
Brand: Multitech Pages: 2
Balluff BIC 1I12-P2A25-M30MI1-BPX05-110 User Manual preview
BIC 1I12-P2A25-M30MI1-BPX05-110
Brand: Balluff Pages: 12
H3C LSWM12H2Q User Manual preview
LSWM12H2Q
Brand: H3C Pages: 9
ETL TeleCLIENT TC7730 Series User Manual preview
TeleCLIENT TC7730 Series
Brand: ETL Pages: 83
XtendLan XL-IPM401 User Manual preview
XL-IPM401
Brand: XtendLan Pages: 21
Ariesys AMK Series User'S Reference Manual preview
AMK Series
Brand: Ariesys Pages: 10
Nvidia GEFORCE RTX 4090 Quick Start Manual preview
GEFORCE RTX 4090
Brand: Nvidia Pages: 160
Amphenol C2LINX Series Installation Manual preview
C2LINX Series
Brand: Amphenol Pages: 43
ADTRAN ENHANCED PSD 239 H2R Product Manual preview
ENHANCED PSD 239 H2R
Brand: ADTRAN Pages: 2

Brands by name

Popular brands

Load more brands