Texas Instruments OMAP36 Series Technical Reference Manual Download Page 825

Page: 825 / 3738

Public Version

www.ti.com

IVA2.2 Subsystem Register Manual

Bits

Field Name

Description

Type

Reset

0x4:

5th highest priority

0x5:

6th highest priority

0x6:

7th highest priority

0x7:

Lowest priority

15:0

Reserved

Write 0s for future compatibility.

0x00000

Read returns 0.

Table 5-79. Register Call Summary for Register MDMAARBE

IVA2.2 Subsystem Basic Programming Model

•

Prioritizing Defined Transfers

[0] [1] [2]

•

Internal Memory

[3] [4] [5] [6] [7]

IVA2.2 Subsystem Register Manual

•

IDMA Register Mapping Summary

[8]

Table 5-80. ICFGMPFAR

Address Offset

0x0000 0300

Physical address

0x0182 0300

Instance

IVA2.2 GEMIDMA

Description

ICFG Memory Protection Fault Address Register

Type

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

ADDR

Bits

Field Name

Description

Type

Reset

31:0

ADDR

Fault Address

0x00000000

Table 5-81. Register Call Summary for Register ICFGMPFAR

IVA2.2 Subsystem Basic Programming Model

•

Internal Memory

[0]

IVA2.2 Subsystem Register Manual

•

IDMA Register Mapping Summary

[1]

Table 5-82. ICFGMPFSR

Address Offset

0x0000 0304

Physical address

0x0182 0304

Instance

IVA2.2 GEMIDMA

Description

ICFG Memory Protection Fault Status Register

Type

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

Reserved

FLTID

ATYP

Reserved

Bits

Field Name

Description

Type

Reset

31:16

Reserved

Write 0s for future compatibility.

0x0000

Read returns 0.

15:8

FLTID

Faulted ID:

0x00

VBUS PrivID of faulting requestor. This field is valid only if LE is
zero.

825

SWPU177N – December 2009 – Revised November 2010

IVA2.2 Subsystem

Summary of Contents for OMAP36 Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OMAP36 Series

Reviews:

Texas Instruments OMAP36 Series, Technical Reference Manual, Page: 825 / 3738

Search results

Summary of Contents for OMAP36 Series

Reviews: