manualshive.com logo in svg

Texas Instruments OMAP36 Series, Technical Reference Manual, Page: 472 / 3738

Share
Download
Texas Instruments OMAP36 Series Technical Reference Manual Download Page 472

Public Version

PRCM Register Manual

www.ti.com

Bits

Field Name

Description

Type

Reset

31:5

RESERVED

Write 0s for future compatibility. Read returns 0.

R

0x0000000

4:0

MPU_DPLL_CLKOUT_DIV

DPLL1 output clock divider factor (1 up to 16); Other

RW

0x01

enums: Reserved

0x1: DPLL1 CLKOUTX2 divided by 1

0x2: DPLL1 CLKOUTX2 divided by 2

0x3: DPLL1 CLKOUTX2 divided by 3

0x4: DPLL1 CLKOUTX2 divided by 4

0x5: DPLL1 CLKOUTX2 divided by 5

0x6: DPLL1 CLKOUTX2 divided by 6

0x7: DPLL1 CLKOUTX2 divided by 7

0x8: DPLL1 CLKOUTX2 divided by 8

0x9: DPLL1 CLKOUTX2 divided by 9

0xA: DPLL1 CLKOUTX2 divided by 10

0xB: DPLL1 CLKOUTX2 divided by 11

0xC: DPLL1 CLKOUTX2 divided by 12

0xD: DPLL1 CLKOUTX2 divided by 13

0xE: DPLL1 CLKOUTX2 divided by 14

0xF: DPLL1 CLKOUTX2 divided by 15

0x10: DPLL1 CLKOUTX2 divided by 16

Table 3-132. Register Call Summary for Register CM_CLKSEL2_PLL_MPU

PRCM Functional Description

•

Processor Clock Configurations

:

[0]

PRCM Basic Programming Model

•

CM_CLKSELn_PLL_ <processor_name> (Processor DPLL Clock Selection Register)

:

[1]

PRCM Register Manual

•

MPU_CM Register Summary

:

[2]

Table 3-133. CM_CLKSTCTRL_MPU

Address Offset

0x0000 0048

Physical Address

0x4800 4948

Instance

MPU_CM

Description

This register enables the domain power state transition. It controls the HW supervised domain power
state transition between ACTIVE and INACTIVE states.

Type

RW

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

9

8

7

6

5

4

3

2

1

0

RESERVED

CLKTRCTRL_MPU

472

Power, Reset, and Clock Management

SWPU177N – December 2009 – Revised November 2010

Copyright © 2009–2010, Texas Instruments Incorporated

Summary of Contents for OMAP36 Series



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments