Texas Instruments OMAP36 Series Technical Reference Manual Download | Manualshive

Page: 3617 / 3738

background image

Public Version

www.ti.com

SDTI Module

27.3.4.6 CoreSight Integration Mode

As a CoreSight-compliant peripheral, the SDTI provides an integration mode where the interface input
ports can be probed and the output ports can be driven. The following CoreSight integration registers are
used to set up and use this mode:
•

INT_MODE_CTRL_REG

•

•

The

CLAIM_TAG_SET_REG

register is included for CoreSight compliance. Normally, the lower 4 bits are

used for claiming and releasing debug components. The SDTI, however, implements a more sophisticated
claim mechanism. These bits can be used as software semaphores to help manage the debug resources,
although the claim-and-enable mechanism of the SDTI resources must still be used. Writing 1 to one of
the set bits causes the corresponding bit in the claim tag value word to go high.

The

CLAIM_TAG_CLEAR_REG

bits can be used as software semaphores to help manage the debug

resources. Writing 1 to one of the CLEAR bits causes the corresponding bit in the claim tag value word to
go low. Reading this register returns the value of the claim tag.

27.3.4.7 Serial Interface Clock Generation

The sdti_clk is derived from SDTI_FCLK with a programmable clock divider controlled by the

[3:0] SDTISCLKRATE bit field.

shows the divider for the value of the

[3:0] SDTISCLKRATE bit field.

Table 27-38. sdti_clk Divider Value

SDTISCLKRATE Value

Division Value

0x0

Division by 1

0x1

Division by 1

0x2

Division by 2

0x3

Division by 3

0x4

Division by 4

0x5

Division by 5

0x6

Division by 6

0x7

Division by 7

0x8

Division by 8

0x9

Division by 9

0xA

Division by 10

Others

Division by 1

27.3.4.8 SDTI Memory Mapping

shows the SDTI memory mapping, and

provides channel address examples.

Table 27-39. SDTI Memory Mapping

Name

Address Offset

Address

Size

Start

Stop

Start

Stop

Configuration Space (Base = 0x5450 0000)

4k

Configuration Registers

0x0 0000

0x0 002F

0x5450 0000

0x5450 002F

48

Reserved

0x0 0030

0x0 0EFF

0x5450 0030

0x5450 0EFF

3792

CoreSight Registers

0x0 0F00

0x0 0FFF

0x5450 0F00

0x5450 0FFF

256

Reserved

0x0 1000

0xF FFFF

0x5450 1000

0x545F FFFF

Window Space (Base = 0x5460 0000)

1024k

Channel 0

0x00 0000

0x00 0FFF

0x5460 0000

0x5460 0FFF

4k

CPU1 message

0x00 0000

0x00 03FF

0x5460 0000

0x5460 03FF

1k

3617

SWPU177N – December 2009 – Revised November 2010

Debug and Emulation

Copyright © 2009–2010, Texas Instruments Incorporated

«
...
3615
3616
3617
3618
3619
...
»

Summary of Contents for OMAP36 Series



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP36 Series

Professional Series

Brand: PACOM Pages: 15

Brand: National Instruments Pages: 9

FIELDPOINT FP-1600

Brand: National Instruments Pages: 8

Brand: Avolites Pages: 24

Brand: T.A Pages: 11

Brand: PADAUK Pages: 27

cPCIS-1100 Series

Brand: ADLINK Technology Pages: 48

LinkStation 500

Brand: Buffalo Pages: 139

Brand: Renesas Pages: 6

Brand: SilverStone Pages: 2

i.MX 8M Mini LPDDR4 EVK

Brand: NXP Semiconductors Pages: 20

Brand: Foxconn Pages: 1

Brand: Paradyne Pages: 46

Brand: Datavideo Pages: 71

Brand: AMD Pages: 10

GigaVUE H Series

Brand: Gigamon Pages: 55

Brand: Radionics Pages: 100

Brand: Lenze Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands