background image

EVM Hardware Overview

www.ti.com

4

SLAU727 – August 2017

Submit Documentation Feedback

Copyright © 2017, Texas Instruments Incorporated

DAC8771 Evaluation Module

2.2

Electrostatic Discharge Warning

Many of the components on the EVM are susceptible to damage by electrostatic discharge (ESD). Users
are advised to observe proper ESD handling precautions when unpacking and handling the EVM,
including the use of a grounded wrist strap at an approved ESD workstation.

2.3

Jumper Summary

Table 3

summarizes all of the EVM jumper functionality.

Table 3. EVM Jumper Summary

Jumper Label

Default

Position

Function

JP1

1-2

1-2

Selects positive buck-boost to supply VPOS

2-3

Selects PVDD/AVDD to supply VPOS

JP2

1-2

1-2

Selects negative buck-boost to supply VNEG

2-3

Selects EXT_VNEG to supply VNEG

JP3

Installed

Installed

VSENSEP is shorted to VOUT onboard

Not installed

VSENSEP is shorted to VOUT off board

JP4

Installed

Installed

Loads VOUT/IOUT with a short to GND

Not installed

Unloads VOUT/IOUT of the short to GND

JP5

Installed

Installed

Loads VOUT/IOUT with a 249-

Ω

resistor

Not installed

Unloads VOUT/IOUT of the 249-

Ω

resistor

JP6

Not installed

Installed

Loads VOUT/IOUT with a 624-

Ω

resistor

Not installed

Unloads VOUT/IOUT of the 625-

Ω

resistor

JP7

Not installed

Installed

Loads VOUT/IOUT with a 1-k

Ω

resistor

Not installed

Unloads VOUT/IOUT of the 1-k

Ω

resistor

JP8

Installed

Installed

VSENSEN is shorted to GND onboard

Not installed

VSENSEN is shorted to GND off board

JP9

Installed

Installed

When HART_IN is not in use, AC couple to GND

Not installed

When HART_IN is in use, disconnect from GND

JP10

Not installed

Installed

Selects the external DVDD

Not installed

Disconnects the external DVDD

JP11

1-2

1-2

Selects the DAC8771 internal reference

2-3

Selects the REF5050 external reference

JP12

2-3

1-2

Issues a clear command to the DAC8771

2-3

No operation

JP13

Not installed

Installed

Issues a hardware reset to the DAC8771

Not installed

No operation

JP14

Installed

Installed

Select asynchronous update mode

Not installed

Select asynchronous update mode

JP15

Not installed

Installed

Disables internal DVDD LDO

Not installed

Enables internal DVDD LDO

JP16

Not installed

Installed

Connects the SM-USB-DIG supply to DVDD

Not installed

Disconnects SM-USB-DIG supply for DVDD

JP17

Not installed

Installed

RSET is connected to external Resistor

Not installed

Internal current setting resistor is used

Summary of Contents for DAC8771EVM

























Reviews: