background image

www.ti.com

2

SLAU773 – May 2018

Submit Documentation Feedback

Copyright © 2018, Texas Instruments Incorporated

DAC5652AEVM User's Guide

1

Introduction

...................................................................................................................

3

2

Power Requirements

........................................................................................................

4

3

Schematic Diagram

..........................................................................................................

4

4

Device Modes and Settings

................................................................................................

6

5

Input Data Mode

.............................................................................................................

6

6

Quick-Start Procedure

.......................................................................................................

6

List of Figures

1

DAC5652AEVM Setup Diagram

...........................................................................................

3

List of Tables

1

Input Connector J9

..........................................................................................................

5

2

Transformer Output Configuration

.........................................................................................

5

Summary of Contents for DAC5652AEVM













Reviews: