Texas Instruments AM1808 Technical Reference Manual Download Page 1803

Page: 1803 / 1820

www.ti.com

Registers

1803

SPRUH82C – April 2013 – Revised September 2016

Submit Documentation Feedback

Video Port Interface (VPIF)

35.3.19 Channel n Top Field Vertical Ancillary Address Register (CnTVANC)

The Channel

Top Field Vertical Ancillary Address Register (C

TVANC) is shown in

Figure 35-36

and

described in

Table 35-24

Figure 35-36. Channel n Top Field Vertical Ancillary Address Register

(CnTVANC)

TVANC

R/W-0

LEGEND: R/W = Read/Write; -

= value after reset

Table 35-24. Channel n Top Field Vertical Ancillary Address Register (CnTVANC)

Field Descriptions

Bit

Field

Value

Description

31-0

TVANC

0-FFFF FFFFh

Memory address of the top field vertical ancillary buffer.

The register value points to the beginning of the buffer, and the address must be a multiple of 8
(C

TVANC[2:0] = 0).

35.3.20 Channel n Bottom Field Vertical Ancillary Address Register (CnBVANC)

The Channel

Bottom Field Vertical Ancillary Address Register (C

BVANC) is shown in

Figure 35-37

and

described in

Table 35-25

NOTE:

BVANC registers are not used in progressive video mode.

Figure 35-37. Channel n Bottom Field Vertical Ancillary Data Buffer Start Address Register

(CnBVANC)

BVANC

R/W-0

LEGEND: R/W = Read/Write; -

= value after reset

Table 35-25. Channel n Bottom Field Vertical Ancillary Data Buffer Start Address Register

(CnBVANC)

Field Descriptions

Bit

Field

Value

Description

31-0

BVANC

0-FFFF FFFFh

Memory address of the bottom field vertical ancillary buffer.

The register value points to the beginning of the buffer, and the address must be a multiple of 8
(C

BVANC[2:0] = 0).

«
...
1801
1802
1803
1804
1805
...
»

Summary of Contents for AM1808





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for AM1808

Reviews:

Related manuals for AM1808

Brands by name

Popular brands

Texas Instruments AM1808, Technical Reference Manual

Search results

Summary of Contents for AM1808

Reviews:

Related manuals for AM1808

Brands by name

Popular brands