background image

User's Guide

SBAU213 – September 2013

ADS8860EVM-PDK

This user's guide describes the operation and use of the

ADS8860

evaluation module (EVM). The

ADS8860 is a 16-bit, pseudo-differential, unipolar, successive approximation register (SAR), analog-to-
digital converter (ADC) with a maximum throughput of 1 MSPS. The device is a very low-power ADC with
excellent noise and distortion performance for ac or dc signals. The performance demonstration kit (PDK)
eases EVM evaluation with additional hardware and software for computer connectivity through a
universal serial bus (USB). The

ADS8860EVM-PDK

includes the ADS8860EVM as a daughter card,

MMB0 motherboard, A-to-B USB cable, and 6-V wall-adapter power supply. This user's guide covers
circuit description, schematic diagram, and bill of materials for the ADS8860EVM daughter card.

ADS8860EVM-PDK

Contents

1

Related Documentation

....................................................................................................

2

2

ADS8860EVM-PDK Overview

.............................................................................................

3

3

EVM Analog Interface

......................................................................................................

4

4

EVM Digital Interface

.......................................................................................................

6

5

EVM Power-Supply Inputs

.................................................................................................

7

6

EVM Digital Configuration

.................................................................................................

8

7

PDK Kit Setup

...............................................................................................................

9

8

PDK Kit Operation

.........................................................................................................

11

9

Bill of Materials, Schematics, and Layout

..............................................................................

14

ADCPro is a trademark of Texas Instruments.
Windows is a registered trademark of Microsoft Corporation.
I

2

C is a trademark of NXP Semiconductors.

Samtec is a trademark of Samtec, Inc.
All other trademarks are the property of their respective owners.

1

SBAU213 – September 2013

ADS8860EVM-PDK

Submit Documentation Feedback

Copyright © 2013, Texas Instruments Incorporated

Summary of Contents for ADS8860EVM-PDK





















Reviews: