12
For further information, see the user manual which is
included with the charger.
Important:
The charger will stop, when the battery is
full. However, it is not recommended to leave the
battery in charger for more than 24 hours.
It is recommended to drain the battery completely and
fully charge it whenever possible, as it can increase
the health of the battery. But partial charge will not
damage the battery.
To remove the battery from the charger, hold the
button down and pull the battery out.
Before winter storage, the battery should be fully
charged and kept warm at 10-20 degrees C. Charge it
every 3 months. Make sure to keep ventilation holes
clean and free from dirt.
Store the charger indoor between 5-25 degrees C.
6. Use
See Fig. 5
Before use, make sure that the battery is fitted properly
with the battery lock in place.
To start the machine first press the main switch (A), so
the power indicator lights green. Then hold the safety
switch (B) and activate the trigger switch (C).
Stop the machine by releasing the trigger switch (C).
Stop ved at slippe aktiveringsknappen (C). Always
remove the battery, when the machine is not being
used.
Press the speed button (D) to choose between normal
speed and turbo speed.
Turbo speed will consume the power faster, and should
only be used when neccesary.
Automatic switch off function
The machine is equipped with a switch off function that
deactivated the machine if not used within approx. 60
seconds. The green power indicator light will switch off
too. Press the main switch (1) to restart.
Important when using:
•
When the engine is stopped the rotating blade
must be held in grass or bush until it holds still.
•
Always hold the machine with both hands.
•
The machine must not be used if the safety guard
is not correctly fitted and in mint condition.
•
Always stop the engine before attempting to
remove objects that may have stuck on the blade.
•
Never touch or try to stop the blade while it is still
spinning.
•
A rotating blade may cause damage, as it
continues to spin after the engine has stopped or
the gas has been turned off. Always be in control of
the tool until the blade has stopped spinning.
•
Always make sure that the blade is mounted
securely and correctly before every time is used.
•
Only use a sharp blade. Replace blades that are
worn or damaged.
•
Only use original spare parts.
•
Only use the blade for weeds, grass and similar.
•
Throw back is something that may occur when the
rotating blade gets into contact with something, it
cannot cut. This contact may have the effect, which
the blade stops for a moment, and suddenly the
tool is thrown away from the hard object that was
hit. This reaction may be so violent that the user
loses control of the tool. Throw back may occur
without warning if the blade is stuck, loses speed or
impeded. This is most likely in areas where it is
difficult to see the material that is being cut.
•
The harness must always be used and adjusted to
fit in the correct manner.
•
Keep a firm grip on both handles while the blade is
running. Keep the blade away from your body and
below your waist.
•
See Fig. 9 for working direction for trimmer head
and with blade.
7. Clothing
When using the machine, wear tight-fitting work clothes,
strong working gloves, hearing protectors, safety
goggles and boots with non-skid soles
8. Tips and advices
Trimming. See Fig. 6A
Hold the trimmer head just above the ground at an
angle. It is the end of the line that does the work. Let
the line work at its own pace. Never press the line into
the area to be cut.
Cutting. See Fig. 6B
The trimmer is ideal for cutting grass that is difficult to
reach using a normal lawn mower. Keep the line
parallel to the ground when cutting. Avoid pressing the
trimmer head against the ground as this can ruin the
lawn and damage the tool.
Do not allow the trimmer head to constantly come into
contact with the ground during normal cutting, as this
can cause damage and wear to the trimmer head.
Only bump the trimmer head against the ground to
release more nylon line.
Sweeping. See Fig. 6C
The fan effect of the rotating line can be used for quick
and easy clearing up. Hold the line parallel to and
above the area to be swept and move the trimmer head
from right to left and opposite.
When cutting and sweeping you should use full
throttle to obtain the best results.
3-tooth blade.
It is used to cut through dense vegetation,
