TEVA TPA Series Service Manual Download Page 7

- 7 -

2º) SECCIONES SUPERIORES

Colocadas, atornilladas y ancladas todas las secciones
inferiores, se procederá a la colocación de las secciones
superiores, empezando por una de las secciones del
extremo, de forma que coincidan los taladros de la base con
los correspondientes de la sección inferior, ayudándose con
un punzón en cada frontal, si fuese necesario.
Estas primeras secciones, superior e inferior, del extremo,
deberán atornillarse entre sí para evitar posteriores
desplazamientos. Previamente habrá que eliminar la red
plástica que impide el desplazamiento del relleno durante el
transporte.

Para facilitar el acercamiento entre las secciones superiores,
los módulos están dotados de tres puntos reforzados en los
que mediante tres tornillos es posible dicho acercamiento.
Ver detalle “C” en página 8.
Una vez unidos dos módulos adosados atornillarlos entre sí
además de los tornillos que han servido para su
acercamiento, por los superiores indicados en los detalles “A”
cuando se trata de los módulos que conforman una celda y
según el detalle “B” cuando se trate de celdas adosadas.

2º)

UPPER SECTIONS

Placed, screwed and anchored all the lower sections, the
upper sections will be emplaced, beginning by one of the
external sections, in such a way that the holes on the base
coincides with the holes of the lower section, helping with one
awl on each frontal, if it’s needed.
These first sections, upper and lower of the extreme module,
must to be screwed between them in order to avoid
subsequent displacements. Previously the plastic net that
prevent the movement of the filling during the transport must
be removed.

In order to make easier the approximation between the upper
sections, the modules are provided of three reinforced points
since where, through three screws makes possible the
mentioned approximation.
See detail “C” page 7.
Once two adjacent modules have been united and fixed the
screws used for the approximation between modules, the
superior part must be screwed on as indicated in detail “A”
when it comes to two modules that make up a cell and
according detail “B” when it comes to adjacent cells.

Summary of Contents for TPA Series





















Reviews: