Testomat CL Operating Instructions Manual Download

Page: 36 / 52

Description of the signal inputs and outputs

Error number/error
message

Description, possible
causes

Reaction of the
device

Solution, trouble-
shooting measures

31 Fault dosing
pump 2

Dosing pump 2 is defec-
tive

Interval opera-
tion is stopped
Measurement
phase is can-
celled.

•

Check the cable to

the pump to ensure
a correct connection

•

Replace the pump

and enter the new
run time

33 Fault optics
LED1

Error in the optical unit
(light source defective)

Interval opera-
tion is stopped
Measurement
phase is can-
celled.

Change the measure-
ment chamber mount-
ing

27 Fault optics
LED2

Error in the optical unit
(light source defective)

Interval opera-
tion is stopped
Measurement
phase is can-
celled.

Change the measure-
ment chamber mount-
ing

82 Fault optics
BPW

Error in the optical unit (re-
ceiver defective)

Interval opera-
tion is stopped
Measurement
phase is can-
celled.

Change the measure-
ment chamber mount-
ing

80 Fault optics
Imin

Automatic zero-point ad-
justment at the lower stop
not possible
or
automatic zero-point ad-
justment at stop

Interval opera-
tion is stopped
Measurement
phase is can-
celled.

Avoid extraneous light

81 Fault optics
Imax

Automatic zero-point ad-
justment at the lower stop
not possible
or
automatic zero-point ad-
justment at stop

Interval opera-
tion is stopped
Measurement
phase is can-
celled.

•

Clean sight glasses

•

Change the meas-

urement chamber
mounting

34 Fault
Turbidity

The water is too turbid/
soiled

Interval opera-
tion is stopped
Measurement
phase is can-
celled.

Install an upstream wa-
ter filter

35 Fault soiling

The sight-glass windows
are soiled

Interval opera-
tion is stopped
Measurement
phase is can-
celled.

Clean the sight-glass
windows

37 Reagent low

Reagent stock has de-
creased to 10%

Interval opera-
tion is continued

See Reagent shortage
on page 37

12 Meas. range
exceeded

Measurement scope is ex-
ceeded

Interval opera-
tion is stopped

•

Check measuring

chamber and drain
hoses for correct in-
stallation/blocking

•

Are all plugs present

and sit correctly?

Summary of Contents for CL





















































Search results

Summary of Contents for CL

Reviews:

Related manuals for CL

Brands by name

Popular brands

Testomat CL, Operating Instructions Manual

Search results

Summary of Contents for CL

Reviews:

Related manuals for CL

Brands by name

Popular brands