manualshive.com logo in svg

TESTING 1.0330, Operating Manual

Share
Download
TESTING 1.0330 Operating Manual Download Page 19

 
 
Cabinet for Moist Storage 
of Mortar Prisms in Triple Moulds 
1.0330 
 

19  

TROUBLE 

CAUSE 

SOLUTION 

 
The humidifier is producing too much 
moisture.  
 
 
The humidifying pipes are not in their 
correct positions.  
 
There is no air circulation. The internal 
fans are defective. 

 
The controller settings are not correct. 
Get in touch with the manufacturer. 
 
 
Get in touch with the manufacturer. 
 
 
Replace the circulation fans. 
 

The interior of the Cabi-
net is too dry. 

The water supply is not functioning 
properly.  
 
The humidifier is not switched on, or it 
switched itself off. 

If using a water tank

:  refill with dis-

tilled water.  
 
Check to make sure the water supply 
is properly functioning. Get in touch 
with the manufacturer. 

The interior of the Cabi-
net is too warm. 

The cooling system is defective. The 
controller or the sensors are defective. 
The controller settings are not correct. 
The fans are defective. There is no 
proper air circulation. 

Get in touch with the manufacturer. 

 

The interior of the Cabi-
net is too cold. 

The heating system is defective. The 
controller or the sensors are defective. 
The controller settings are not correct. 
The fans are defective. There is no 
proper air circulation. 

Get in touch with the manufacturer. 

 

The controllers do not 
show a measured 
value, although the 
main switch is ON. 

Excessive voltage. Short circuit.  

 

The miniature circuit breakers have 
been turned OFF. 

Take off the front panel of the Cabinet 
and turn ON the miniature circuit 
breakers in the electrical box. Find out 
why the circuit breakers tripped. Get 
in touch with the manufacturer. 

 

6. 

Placing the system out of operation 

 
If the Cabinet should be placed out of operation for a lengthy period of time, it must be 
disconnected from the mains power supply. Then, during this time, conduct all mainte-
nance on the system that is required. Drain or remove the water from all storage tanks. 
Cover the Cabinet to protect it from dust. Keep the door open in order to prevent unpleas-
ant smells. 
 
If the humidifier is not used over longer periods of time, the water must be drained.  
 

7. 

Scrapping the system 

 
If the Cabinet cannot be further used, we recommend scrapping it as follows: 
 

  Disconnect the equipment from the mains power  

  Drain all the water out of the system 

  Dispose of the refrigerant in accordance with currently valid laws. 

  Take the system apart and scrap it in accordance with currently valid laws. 

 
 

 

Summary of Contents for 1.0330























Reviews:

No comments

Brands by name

Popular brands

Load more brands