Test Equipment Depot AMPROBE WT-80 User Manual Download Page 5

Page: 5 / 25

WT-80 pH / ORP Meter

CONTENTS

SYMBOLS

...............................................................................................................2

UNPACKING AND INSPECTION

............................................................................2

INTRODUCTION

.....................................................................................................3

Features ............................................................................................................3

OPERATION

............................................................................................................3

Starting Up .......................................................................................................3

Auto Power Off ................................................................................................5

Setup .................................................................................................................5

Calibration (pH Probe Only) ............................................................................8

SPECIFICATIONS

....................................................................................................8

MAINTENANCE AND REPAIR

................................................................................9

Battery Replacement .......................................................................................11

USB PC Interface Capabilities ..........................................................................11

TROUBLE SHOOTING

.............................................................................................11

MSDS

......................................................................................................................13

Test Equipment Depot - 800.517.8431 -

99 Washington Street Melrose, MA 02176

TestEquipmentDepot.com

Summary of Contents for AMPROBE WT-80

























Search results

Summary of Contents for AMPROBE WT-80

Reviews:

Related manuals for AMPROBE WT-80

Brands by name

Popular brands

Test Equipment Depot AMPROBE WT-80, User Manual

Search results

Summary of Contents for AMPROBE WT-80

Reviews:

Related manuals for AMPROBE WT-80

Brands by name

Popular brands