background image

C) Do not operate tool without guards in place. 

D) Do not perform any operation freehand. 

E) Never reach around cutting tools. 

F) Turn off tool and wait for cutting tools to stop before moving workpiece or changing settings. 

G) Disconnect power (or unplug tool) before changing cutting tools or servicing. 

 

 

GENERAL SAFETY INSTRUCTIONS 

Read this owner's manual completely and make sure you understand all of its safety 
guidelines

 

1. KEEP GUARDS IN PLACE and in working order. 

2. REMOVE ADJUSTING KEYS & WRENCHES. Before turning on the power tool, make sure the 
keys and adjusting wrenches have been removed. 

3. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents. 
4. ALWAYS REMAIN ALERT WHEN THE TOOL IS IN USE. Inattention on the part of the 

operator may lead to serious injury. 

5. DON’T USE IN A DANGEROUS ENVIRONMENT. Don’t use power tools in damp or wet 

locations or expose them to rain. Keep work area well lit. 

6. KEEP CHILDREN AWAY. All visitors should remain at a safe distance from work area. 
7. MAKE WORKSHOP CHILD-PROOF with padlocks, master switches or by removing starter keys. 

8. USE THE RIGHT TOOL. Don’t force a tool or attachment to do a job for which it was not 
designed. 

9. USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. 

When using an extension cord, be sure to use one heavy enough to carry the current your product 

will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and 

overheating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier 

the cord. 

10. DON’T FORCE THE TOOL. It has been designed to operate at maximum safety and 
performance levels. 

11. DO NOT FORCE THE MATERIAL BEING CUT. Always let the tool cut at its own speed. 

12. WEAR PROPER APPAREL. Do not wear loose clothing, neckties, rings, bracelets or other 

jewelry which may get caught in moving parts. Non-slip foot wear is recommended. Wear 

protective hair covering if you have long hair. 

13. ALWAYS USE SAFETY GLASSES. Also use face or dust mask for commercial cutting 

operations. Everyday eyeglasses only have impact-resistant lenses, they are NOT safety glasses. 

14. SECURE WORK. Use clamps or a vise instead of your hand to hold work when practical. This 

safety precaution allows for proper tool operation using both hands. 

15. DON’T OVERREACH. Keep proper footing and balance at all times. 

16. MAINTAIN TOOLS WITH CARE. Keep tools clean and in good working condition for 

maximum safety performance. Follow instructions for lubricating and changing accessories. 

17. DISCONNECT TOOLS BEFORE SERVICING – when changing accessories, such as blades, 

bits, cutters, etc. 

18. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in OFF position 

before plugging in. 

19. USE RECOMMENDED ACCESSORIES. Consult the owner’s manual for recommended 
accessories. The use of improper accessories may increase risk of injury. 

20. MAKE SURE YOU USE THE CORRECT TOOL for the job you are doing. 

21. NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool 

is unintentionally contacted. 

22. CHECK DAMAGED PARTS. Before further use of the tool, damaged part(s), (i.e., guard) 

should be carefully checked to determine that it will operate properly and perform its intended 

function. Check for alignment of moving parts, binding of moving parts, breakage of parts, 
mounting and any other condition that may affect the tools operation. A guard or other part that is 

damaged should be properly repaired or replaced. 
23. Replace damaged blades/cutters immediately. DO NOT USE DAMAGED BLADES/CUTTERS. 

They may cause bodily injury. 

24. DIRECTION OF FEED. Feed work into the blade/cutter against the direction of rotation of the 

blade/cutter only. 

25. DO NOT ALTER THE PLUG. 

Summary of Contents for TPMT15VBE
















Reviews: