background image

Read and Keep This Manual 

Please read carefully all instructions within this manual.  Failure to follow all safety warnings can 

result in serious personal injury.  The term “Power Tool” in all of the following warnings refers to 

your mains operated (corded) or battery operated (cordless) power tool 

 

Important SAFETY Information 

 

 

 

 

 

 

 

 

 

General Safety Rules 

 

WARNING!  Read all instructions.  Failure to follow all instructions listed 

below may result in electric shock, fire and/or serious injury.  The term 

“power tool” in all of the warnings listed refers to corded or cordless power 
tools. 

 

Work area safety   

Keep work area clean and well lit.  Cluttered or dark areas invite accidents. 

Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, 

gases or dust.  Power tools create sparks which may ignite the dust or fumes. 

Keep children and bystanders away while operating a power tool.  Distractions can cause you to 
lose control. 

 

Electrical safety   

  This symbol is to warn you of potential personal 

injury hazards.  Please read carefully the notes alongside this 

warning to avoid possible injury or death. 

Summary of Contents for TPMT15VBE
















Reviews: