Terranova Scientific 921 Instruction Manual Download Page 8 | Manualshive

Page: 8 / 22

background image

D U N I W A Y S T O C K R O O M C O R P .

W W W . D U N I W A Y . C O M

8 of 22

11. Analog Output

calibrated, 12-bit resolution, logarithmic, 0.50 volts/decade

12. RS-232 Input/Output

allows user to read pressure and set points; 9600 baud, 8-N-1; available through the D15 acces-
sory connector

13. Operating Voltage

the Model 921 has a universal power supply, which operates on input voltages from 85

VAC

to

265

VAC

50/60 Hz; standard IEC 320 instrument power input receptacle on rear panel; replace-

ment fuse type: 5 mm X 20 mm, regular 1 amp

manufacturer

fuse type

Bussman

GDB-1A or GDC-1A

Littlefuse

217 001 or 218 001

14. Weight

1 lb. / 0.5 kg

15. Mounting

Side clips are provided for panel mounting in standard 1/8 DIN cutout.

16. Environmental Considerations

not for use with explosive or corrosive gases

17. Vacuum gauge tube:

the HPS Cold Cathode (Inverted Magnetron) and cable are available from Duniway Stockroom
or HPS:

Duniway Stockroom
tel (800) 446-8811 or (650) 969-8811 (California)
Facsimile (650) 965-0764

Inverted Magnetron Gauge: Duniway part no. IMAG-CFF
Inverted Magnetron Cable: Duniway part no. IMAG-CBL

HPS Division of MKS Instruments
tel. (800) 345-1967; (303) 449-9861 (Colorado)
Facsimile (303) 442-6880

TELEPHONE: 650-969-8811 TOLL-FREE (U.S. only): 800-446-8811 FAX: 650-965-0764 EMAIL: [email protected]

www.duniway.com

«
...
6
7
8
9
10
...
»

Summary of Contents for 921























Reviews:

No comments

Related manuals for 921

Brand: Hach Pages: 2

Brand: Hach Pages: 12

Brand: Hach Pages: 472

Brand: Hach Pages: 64

Brand: V2 ELETTRONICA Pages: 6

Brand: Hach Pages: 210

Brand: V2 ELETTRONICA Pages: 72

Brand: LAS Pages: 6

Brand: Lawler Pages: 4

Brand: QTP Pages: 2

Brand: µ-Dimension Pages: 48

Brand: µ-Dimension Pages: 2

sensoCOMFORT VRC 720/3

Brand: Vaillant Pages: 64

Brand: Sunnen Pages: 24

Brand: Hach Pages: 504

Brand: IBCcontrol Pages: 16

Brand: Advantech Pages: 2

Vizia RF+ VRP15-1LW

Brand: Leviton Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands