Terranova Scientific 921 Instruction Manual Download

Page: 21 / 22

D U N I W A Y S T O C K R O O M C O R P .

W W W . D U N I W A Y . C O M

21 of 22

DECLARATION OF CONFORMITY

We, Duniway Stockroom Corp., declare under our sole responsibility,

that the following products, displaying the CE mark on the rear panel:

Model 906 Convection Gauge Controller

Model 908 Dual Capacitance Diaphragm Gauge Controller

Model 921 Cold Cathode Gauge Controller

Model 924 Thermocouple Vacuum Gauge

Model 926 Dual Convection Gauge Controller

to which this declaration relates, are in conformity with the following

standards or normal documents

EMC Directive (89/336/EEC//93/68/EEC)

Electromagnetic Compatibility

Standards: EN 50081-1: 1992, EN 50082-1: 1993

Low Voltage Directive (73/23/EEC//93/68/EEC)

Electrical/Technical Safety

Standard: EN 61010-1: 1993/A2: 1995

following the provisions of the EMC directive (89/336/EEC)

August 30, 1998

by: Sherman Rutherford

Compliance Manager

Duniway Stockroom Corp.

48501 Milmont Drive

Fremont

, California 94

538

rev092399sr

TELEPHONE: 650-969-8811 TOLL-FREE (U.S. only): 800-446-8811 FAX: 650-965-0764 EMAIL: [email protected]

www.duniway.com

Summary of Contents for 921























Search results

Summary of Contents for 921

Reviews:

Related manuals for 921

Brands by name

Popular brands

Terranova Scientific 921, Instruction Manual

Search results

Summary of Contents for 921

Reviews:

Related manuals for 921

Brands by name

Popular brands