background image

Run button: Once programming parameters have been set for time and function, 

use the Run button to save and exit the programming interface. Press the Run 

button once to run the time program that has been set. 

Hold/Set button: Press the Hold/Set button once and the thermostat will stay in the 

current mode and temperature setting. In heating/cooling mode, pressing the Hold/Set 

button will hold the temperature that it is currently set at and will not change during 

the setting process. In the heating/cooling mode, pressing and holding the Hold/Set 

button for 3 seconds allows you to enter the programming parameter interface. When 

thermostat is Off, pressing and holding the Hold/Set button for 5 seconds allows you 

to enter the programming parameter interface.

Clock and day of the Week Display.

Cool symbol: When the Cool symbol is displayed, the cooling relay has been activated.

When the Cooling symbol is flashing, it means that the cooling relay is in the set-up 

delay process.

Heat Symbol: When the Heating symbol is displayed,the heating relay has been

activated. When the Heating symbol is flashing, it means that the heating relay is in the

set-up delay process.

System Cool Symbol: When the System Cool symbol is displayed, it indicates the

thermostat is in cooling mode.
System Heat Symbol: When the System Heat symbol is displayed, it indicates the 

thermostat is in heating mode.

TENZA

Down button: In heating/cooling mode, the Down button lowers the temperature

setting. When programming, the Down button will be used for changing system

parameters.

Up button: In heating/cooling mode, the Up button raises the temperature setting. 

When programming, the Up button will also be used for changing system 

parameters.
Cool/Heat/Off button: Press once for Cooling Mode. Press twice for Heating Mode.

Press 3 times to turn Off the thermostat.

Fan button: Switches between fan On and Auto. When fan is On, the fan on your

appliance will remain on. In Auto mode the fan will come on only when heating or 

cooling.

Hold symbol: When the Hold symbol is displayed, the Hold button has been activated 

and the current temperature will be held and the thermostat will not follow programmed 

routine.
Room Temperature Display: Displays the current room temperature.

Temperature Setting Display: Displays the current temperature setting.

Low Battery Warning: When this symbol is displayed replace the batteries with 2 new,

high quality AA batteries.

Fan Symbol: Displays the current mode of the fan.
Program Setting Display: Indicates when the system is in the setting process.

Summary of Contents for CPT10







Reviews: