manualshive.com logo in svg

TENX TECHNOLOGY TM57PE10, User Manual

Share
Download
TENX TECHNOLOGY TM57PE10 User Manual Download Page 13

Advance Information 
 

UM-TM57PE10_E 

 8-Bit Microcontroller  

 

13

                           tenx technology inc.  

Preliminary

                                                                                   

Rev 1.4,  2012/01/19 

 

1.6   Interrupt 

The TM57PE10 has 1 level, 1 vector and 8 interrupt sources. Each interrupt source has its own enable 
control bit. An interrupt event will set its individual pending flag; no matter its interrupt enable control bit 
is 0 or 1. Because TM57PE10 has only 1 vector, there is not an interrupt priority register. The interrupt 
priority is determined by F/W. 

If the corresponding interrupt enable bit has been set (INTE), it would trigger CPU to service the 
interrupt. CPU accepts interrupt in the end of current executed instruction cycle. In the mean while, a 
“CALL 001” instruction is inserted to CPU, and i-flag is set to prevent recursive interrupt nesting. 

The i-flag is cleared in the instruction after the “RETI” instruction. That is, at least one instruction in main 
program is executed before service the pending interrupt. The interrupt event is level triggered. F/W 
must clear the interrupt event register while serving the interrupt routine. 

Interrupt Pending

Interrupt 

Vector

i-Flag

Interrupt 

Source

Interrupt 

Enable

 

 

Summary of Contents for TM57PE10
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands