background image

• Locate metal grommet holes, 

   on the underside of the canopy

• Insert pin end of pole

• Start with corner poles

• All four corner poles should be 

   installed FIRST

• Stand poles up—this is done in steps,

   a 60º angle is require, for each corner

   pole—then vertical, after all four 

   corners are ready

• Ropes should be attached

   

• A commonly used knot for securing 

   a rope to stake is the clove-hitch

1.) Make two loops

2.) Cross loops by placing second loop

   over the first

3.) Place the combined loops over stake

   Option: loops can be form directly 

   on stake

4.) Pull on both ends to tighten rope

   Note: outward force tightens and 

   inward force loosens the knot—when

   making adjustments

5.) Excess line should be pulled half-

   way up the rope and tied off

• Grab center pole(s) walk under canopy

   (two people required)

• Insert center pole pin through metal

   plate and grommet, at center of canopy

• To raise pole, have one person hold the 

   pole near the upper half and person 

   two, at the bottom end—raise upward

   and vertical

• For multiple poles; Insert first pole 

   (as above), keep angle at 45 degrees to 

   allow more stability, as you work on the 

   other pole(s)

• Install next center pole in vertical 

   position—then, go back to first pole, 

   lift and adjust to vertical 

STEP 8. RAISING CENTER POLE(S)

60º angle

towards

center

45º angle

towards center

STEP 7. RAISING CORNER POLES

Multiple 

center poles

(cutaway view— showing inside of canopy)

If your tent is 60ft. or longer start with one center pole 

3.)   

   4.)

1.)

2.)

FIGURE B. CLOVE-HITCH KNOT

4

716 832-TENT

 (

8368

)

Summary of Contents for BT-PP48WT4P









Reviews: