Tennant sentinel Operator'S Manual Download

Page: 85 / 150

Sentinel 9018513 (12-2018)

MAINTENANCE

HOPPER TILT (Low Dump)

The hopper tilt (A) has eight grease

ttings. Four

grease

ttings are located on the tilt cylinders,

one on each end of the two cylinders. Two grease

ttings are located on the hopper safety support

cylinders (one at each end). Two grease

ttings

are located at the hopper tilt pivot (one on each
side). Lubricate these

ttings after every 100 hours

of operation.

WARNING: Raised hopper may fall.
Engage hopper support pin.

351933

HOPPER LIFT/TILT (High Dump Option)

The high dump hopper lift (B) has thirteen grease

ttings. Four grease

ttings are located on the

upper tilt cylinders (one on each end of both
cylinders). Two grease

ttings are located on the

lower lift cylinders (one at each base). One grease

tting is located at the top of the hopper safety

support cylinder. Two grease

ttings are located

at the hopper tilt pivot (one on each side). Four
grease

ttings are located on the cross shaft pivots

of the hopper lift arms (one at each of the four
pivots). Lubricate these

ttings after every 100

hours of operation.

351932

WARNING: Raised hopper may fall.
Engage hopper support pin.

AXLE LEAF SPRINGS

The axle leaf springs (C) have twelve grease

ttings. Lubricate the axle leaf springs after every

200 hours of operation.

Summary of Contents for sentinel























































































































































Search results

Summary of Contents for sentinel

Reviews:

Related manuals for sentinel

Brands by name

Popular brands

Tennant sentinel, Operator'S Manual

Search results

Summary of Contents for sentinel

Reviews:

Related manuals for sentinel

Brands by name

Popular brands