Tennant Litter Hawk Operator'S Manual Download Page 76

Page: 76 / 88

MAINTENANCE

Litter Hawk

330470 (12--99)

BRAKES AND TIRES

BRAKES

The brakes on the machine are front wheel disk

brakes. The brakes are operated by the brake

pedal and connecting rods.

Check the brake adjustment after every 200 hours

of operation. If the brake does not respond well to

pressure on the brake pedal, you may need to

adjust the brake.

The foot pedal should not travel more than

25.4 mm (1 in) to engage the brake.

To Adjust Brakes:

Park the machine on a level surface. Turn the

machine off and block the tires.

FOR SAFETY: Before leaving or

servicing machine, stop on level surface

turn off machine and remove key.

Jack up the machine, and remove the left front

tire to access the brake adjustment rod.

FOR SAFETY: When servicing machine,

Block machine tires before jacking up

machine.

Loosen the brake adjustment nuts. Rotate the

brake extension arm and draw the ends inward to

tighten. Secure with adjustment nuts.

Adjust the brake connecting rods so the brake

pedal travels no more than 25.4 mm (1 in) to

engage the brakes. Readjust the brakes if

necessary.

Summary of Contents for Litter Hawk

























































































Search results

Summary of Contents for Litter Hawk

Reviews:

Related manuals for Litter Hawk

Brands by name

Popular brands

Tennant Litter Hawk, Operator'S Manual

Search results

Summary of Contents for Litter Hawk

Reviews:

Related manuals for Litter Hawk

Brands by name

Popular brands