Tennant Litter Hawk Operator'S Manual Download Page 16

Page: 16 / 88

OPERATION

Litter Hawk

330470 (12--99)

WATER PUMP SWITCH

The

water pump switch

controls the two water

pumps for the dust control system. The water

pumps and the lights on the switch will shut off

when the water tank is empty. See the DUST

CONTROL SYSTEM in the MAINTENANCE

section of this manual.

Off: Press the switch to the middle off position to

stop the water pumps.

Side brush pump on: Press the top of the water

pump switch to activate the steady spray dust

control nozzles in front of each side brush. The

light on the switch will come on while the pump

is on.

Debris hopper pump on: Press the bottom of the

water pump switch to activate the pulsating dust

control spray above the debris hopper. The light

on the switch will come on while the pump is on.

Summary of Contents for Litter Hawk

























































































Search results

Summary of Contents for Litter Hawk

Reviews:

Related manuals for Litter Hawk

Brands by name

Popular brands

Tennant Litter Hawk, Operator'S Manual

Search results

Summary of Contents for Litter Hawk

Reviews:

Related manuals for Litter Hawk

Brands by name

Popular brands