Tennant 6550D Operator'S Manual Download Page 24

Page: 24 / 96

OPERATION

6550D 330330 (5--98)

MAIN BRUSH SHUT DOWN LIGHT

The main brush shut down light comes on when

there is excessive down pressure for the main

brush, or there is a problem with the main and

side brush hydraulic motor circuit. The brush

pressures can be reduced with the main brush

and side brush pressure knobs.

FUEL LEVEL GAUGE

The fuel level gauge indicates how much fuel is in

the fuel tank with a segmented LED light. When

the tank is full, all ten of the segments are lit. As

the fuel tank empties, the segments shut off. The

fuel tank is empty when all ten of the segments

have shut off.

NOTE: Do not let the fuel tank empty completely.

Air can enter the fuel system. The fuel system will

need bleeding before the next engine start.

HOURMETER

The hourmeter records the number of hours the

machine has been operated. Use this information

to determine machine maintenance intervals.

07761

07764

07765

Summary of Contents for 6550D

































































































Search results

Summary of Contents for 6550D

Reviews:

Related manuals for 6550D

Brands by name

Popular brands

Tennant 6550D, Operator'S Manual

Search results

Summary of Contents for 6550D

Reviews:

Related manuals for 6550D

Brands by name

Popular brands