background image

OPERATION

Tennant  1500  (02–02)

2

This manual is furnished with each new model. It
provides necessary operation and maintenance
instructions and an illustrated parts list.

Read this manual completely and understand the
machine before operating or servicing it.

When ordering replacement parts use the illustrated
Parts Lists in this manual.  Before ordering parts or
supplies, be sure to have your machine model number
and serial number handy. Parts and supplies may be
ordered by phone or mail from any authorized Service
Center or Distributor.

This machine will provide excellent service. However,
the best results will be obtained at minimum costs if:

S

The machine is operated with reasonable care.

S

The machine is maintained regularly - per the
machine maintenance instructions provided.

S

The machine is maintained with manufacturer
supplied or equivalent parts.

MACHINE DATA

Please fill out at time of installation for future
reference.

Model No.-

Install. Date -

Serial No.-

E

2002 Tennant Company                                    Printed in U.S.A.

Specifications and parts are subject to change without notice.

TABLE OF CONTENTS

SAFETY PRECAUTIONS

3

. . . . . . . . . . . . . . . . . . . . 

MACHINE COMPONENTS

4

. . . . . . . . . . . . . . . . . . . 

CONTROL PANEL SYMBOLS

4

. . . . . . . . . . . . . . . 

MACHINE INSTALLATION

5

. . . . . . . . . . . . . . . . . . . 

UNCRATING MACHINE

5

. . . . . . . . . . . . . . . . . . 

INSTALLING BATTERIES

5

. . . . . . . . . . . . . . . . 

MACHINE SETUP

6

. . . . . . . . . . . . . . . . . . . . . . . . . . 

FILLING SOLUTION TANK

6

. . . . . . . . . . . . . . . 

ADJUSTING CONTROL GRIP HEIGHT

6

. . . . 

MACHINE OPERATION

6

. . . . . . . . . . . . . . . . . . . . . 

PRE–OPERATION CHECKS

6

. . . . . . . . . . . . . . 

WHILE OPERATING MACHINE

7

. . . . . . . . . . . 

CIRCUIT BREAKERS

8

. . . . . . . . . . . . . . . . . . . . 

OPTIONAL ACCESSORY TOOL SETUP AND
OPERATION

8

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

DRAINING TANKS

9

. . . . . . . . . . . . . . . . . . . . . . . . . . 

DRAINING RECOVERY TANK

9

. . . . . . . . . . . . 

DRAINING SOLUTION TANK

9

. . . . . . . . . . . . . 

BATTERY CHARGING

10

. . . . . . . . . . . . . . . . . . . . . . 

MACHINE MAINTENANCE

11

. . . . . . . . . . . . . . . . . . 

DAILY MAINTENANCE 

11

. . . . . . . . . . . . . . . . . . 

WEEKLY MAINTENANCE

11

. . . . . . . . . . . . . . . . 

MONTHLY MAINTENANCE

12

. . . . . . . . . . . . . . . 

QUARTERLY MAINTENANCE

12

. . . . . . . . . . . . 

BATTERY MAINTENANCE

12

. . . . . . . . . . . . . . . 

STORING MACHINE

13

. . . . . . . . . . . . . . . . . . . . . . . . 

TRANSPORTING MACHINE

13

. . . . . . . . . . . . . . . . . 

RECOMMENDED STOCK ITEMS

13

. . . . . . . . . . . . . 

TROUBLE SHOOTING

14

. . . . . . . . . . . . . . . . . . . . . . 

SPECIFICATIONS

15

. . . . . . . . . . . . . . . . . . . . . . . . . . 

ELECTRICAL DIAGRAMS

16

. . . . . . . . . . . . . . . . . . . 

PARTS LIST

18

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

SOLUTION TANK GROUP

18

. . . . . . . . . . . . . . . . 

RECOVERY TANK GROUP

20

. . . . . . . . . . . . . . . 

LIFT GROUP

22

. . . . . . . . . . . . . . . . . . . . . . . . . . . 

BRUSH BASE GROUP

24

. . . . . . . . . . . . . . . . . . . 

DRIVE GROUP

25

. . . . . . . . . . . . . . . . . . . . . . . . . 

PLUMBING GROUP

26

. . . . . . . . . . . . . . . . . . . . . 

CONSOLE GROUP

28

. . . . . . . . . . . . . . . . . . . . . . 

ELECTRICAL / BATTERY GROUP

30

. . . . . . . . 

OPTIONS

32

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

127 mm (5 in) HAND TOOL GROUP

32

. . . . . . . 

76 mm (3 in) CREVICE TOOL GROUP

32

. . . . . 

UPHOLSTERY TOOL GROUP

33

. . . . . . . . . . . . 

330mm (13 in) WAND GROUP

34

. . . . . . . . . . . . 

406mm (16 in) FLOOR TOOL

36

. . . . . . . . . . . . . 

SOLUTION AND VACUUM HOSES GROUP

38

Summary of Contents for 607647







































Reviews: