Tennant 5700XPS Operating Instructions Manual Download Page 14

Page: 14 / 84

OPERATION

5700XPS MM402 (9--95)

SWITCH (OPTION)

The ES

switch turns on and off the solution

recycling system.

On: Press the switch.

Off: Press the switch.

RECOVERY TANK FULL INDICATOR

The recovery tank full indicator comes on when

the recovery tank is full. When the indicator

comes on, the squeegee raises and the vacuum

fan shuts off after a short delay.

SCRUBBING SWITCH

The scrubbing switch controls the scrub brushes,

squeegee and vacuum fan.

Start scrubbing: Press the switch. The indicator

light will come on. The scrubbing system will start

when the steering handles are rotated forward or

backward.

Stop scrubbing: Press the switch. The indicator

light will go off. First the scrub brushes stop and

raise, then vacuum stops and the squeegee

raises.

Summary of Contents for 5700XPS





















































































Search results

Summary of Contents for 5700XPS

Reviews:

Brands by name

Popular brands

Tennant 5700XPS, Operating Instructions Manual

Search results

Summary of Contents for 5700XPS

Reviews:

Brands by name

Popular brands