Tennant 355E Page 15 Operator'S Manual Download | Manualshive

Page: 15 / 72

background image

OPERATION

13

355E MM306 (12–92)

MAIN BRUSH AND SIDE BRUSH LEVER

The main brush and side brush lever controls the
main brush and side brush rotation.

Main Brush and Side Brush On: Push the main
brush and side brush lever into the On position.

Main Brush and Side Brush Off: Pull the main
brush and side brush lever into the middle
position.

Main Brush On: Pull the main brush and side
brush lever into the On position.

NOTE: Always raise the main brush when the
machine is not being operated for some time. This
prevents the main brush from getting a flat spot.

07773

07774

07775

«
...
13
14
15
16
17
...
»

Summary of Contents for 355E









































































Reviews:

No comments

Related manuals for 355E

CHARGER 2022 ABLT

Brand: NSS Pages: 16

Brand: NAMCO Pages: 92

Brand: Rollabind Pages: 2

Brand: Ultratec Pages: 11

Neofold HS 1250

Brand: Neolt Pages: 114

GBC/VeloBind System Three Pro

Brand: Officezone Pages: 7

505 PANTHER PLUS

Brand: National Pages: 27

Brand: JUKI Pages: 84

Brand: JUKI Pages: 4

Brand: Philips Pages: 2

Brand: Philips Pages: 20

Brand: Philips Pages: 36

Brand: Philips Pages: 38

Brand: Philips Pages: 40

Brand: Philips Pages: 36

Brand: Philips Pages: 40

Brand: Philips Pages: 48

magic 3 voice dect

Brand: Philips Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands