manualshive.com logo in svg

Tennant 140, Operator And Parts Manual

Share
Download
Tennant 140 Operator And Parts Manual Download Page 40

MAINTENANCE

140 MM130 (6--91)

3-18

12. Slide the drive wheel retaining bolt through

the frame cutout, the drive wheel, and the

other side frame cutout.

NOTE: Make sure drive wheel spacers removed

earlier are placed in the same positions.

13. Thread the retaining nut onto the retaining

bolt and tighten.

14. Carefully tip the machine back into the

“operating” position.

15. Replace the debris hopper.

16. Adjust the clutch cable as described in

TO

ADJUST FLAT PROPELLING BELT

.

ENGINE DRIVE BELT

The engine drive belt transfers power from the

engine to the vacuum fan and the engine

jackshaft. Check the belt for wear after every

80 hours of operation. There is no tension

adjustment as it is controlled by a belt idler and

spring arrangement.

TO REPLACE ENGINE DRIVE BELT

1. Stop the engine and remove the spark plug

wire.

FOR SAFETY: Before Leaving Or Servicing

Machine; Stop On Level Surface, And Turn Off

Machine And Remove Key.

2. Unlatch and remove the rear filter cover.

3. Remove the rear shroud.

4. Disconnect the belt idler spring from the

engine bracket.

NOTE: For machines equipped with a side brush:

A. Loosen the jackshaft extension support

bearing locking collar setscrew.

01204

LOOSENING JACKSHAFT EXTENSION

SUPPORT BEARING LOCKING COLLAR

B. Unthread and separate the jackshaft

extension from the jackshaft enough to

slide the drive belt through. Also note

that the jackshaft extension is threaded

onto the jackshaft with left hand

threads.

5. Remove existing drive belt.

6. Position new drive belt over vacuum fan

sheave, large diameter sheave, and engine

sheave.

NOTE: For machines equipped with a side brush:

A. Reconnect and tighten the jackshaft

extension to the jackshaft. Remember

the jackshaft extension is threaded onto

the jackshaft with left hand threads.

B. Reposition the jackshaft extension

support bearing locking collar and

tighten its setscrews.

7. Reconnect the belt idler spring to the engine

bracket.

8. Reinstall the rear shroud.

9. Replace the rear filter cover.

Summary of Contents for 140









































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands