manualshive.com logo in svg

Tennant 140, Operator And Parts Manual

Share
Download
Tennant 140 Operator And Parts Manual Download Page 32

MAINTENANCE

140 MM130 (6--91)

3-10

5. Push and lock the main brush removal lever

into place on the machine frame to secure

the main brush.

6. Check and adjust the main brush pattern as

described in

TO CHECK AND ADJUST

MAIN BRUSH PATTERN

.

TO CHECK AND ADJUST MAIN BRUSH
PATTERN

1. Place the machine over a hard floor.

2. Start the engine.

3. Place the main brush lift handle in the

“lower” position to lower the main brush to

the floor for one minute while holding the

machine in one place.

4. Pull the main brush lift handle up and

forward to raise the main brush.

5. Move the machine away from the main

brush polish mark.

6. Stop the engine.

FOR SAFETY: Before Leaving Or Servicing

Machine; Stop On Level Surface, And Turn Off

Machine And Remove Key.

7. Observe the width of the polish mark. The

proper polish width is 1.5 in (40 mm) for

hard floors and 0.5 in (15 mm) for carpet

floors.

A

B

00582

MAIN BRUSH PATTERN

A. Main Brush Pattern

B. Polish Width

If the polish mark width is too wide, turn the main

brush lift handle clockwise to raise the brush.

If the polish mark width is too narrow, turn the

main brush lift handle counterclockwise to lower

the brush.

If any adjustments are made, recheck the main

brush pattern before resuming work with the

machine.

SIDE BRUSH

The side brush sweeps debris from walls or curbs

into the path of the main brush. It should be

inspected daily for wear or damage. Remove any

string or wire found tangled on the side brush or

side brush drive hub.

The side brush should be replaced when the

remaining brush bristle measures 1 in (25 mm) in

length.

The side brush adjustment should be checked

after every 20 hours of operation. The side brush

is properly adjusted when, with the side brush arm

in the “raised” position, there is approximately

1 in (25 mm) of space between the floor and the

side brush bristles.

Side brush adjustments are made by mounting

the side brush in a different one of the five

mounting holes in the side brush drive shaft.

Summary of Contents for 140









































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands