Temspec Air Medic TIF-06 Installation, Operation & Maintenance Manual Download Page 4

 

- 2 - 

2

 

Product Overview  

The Air Medic unit is designed to enhance the air filtration of your primary HVAC system. It does not have the ability to heat or cool 
and  provides  filtration  and  sterilization  only.  This  unit  is  not  a  substitute  for  other  virus  spread  measures  such  as  frequent  hand 
sanitization, face masks or 6ft (2m) physical distancing.  

2.1

 

Model Number 

For the full model numbers available and product selection options please visit our website at 

www.temspec.com

. 

3

 

Operation  

The Air Medic Unit has a few different control options depending on the configuration chosen.  For all units, the Air Medic must be 
plugged into a standard 120V receptacle with ground pin. 

3.1

 

On/Off switch 

If the on/ off switch is chosen it will control the power to the 
unit once plugged in

. The switch will light up when in the “on” 

position to indicate power to the unit. 

If no switch is selected all devices will have power as soon as 
the unit plugged in. 

3.2

 

Filter Clogged Indicator Light 

An optional filter clogged indicator light is available. This light 
is  connected  to  the  differential  pressure  switched.  This 
pressure  switch  measures  the  air  pressure  around  the  HEPA 
filter and when it is too high the indicator light will come on to 
warn the user it should be changed.  

This is only a warning indicator. The unit will continue to work 
with it on, but the airflow will be decreased due to the dirty 
filter.  

3.3

 

Fan Control 

The fan control is available in either variable speed or constant 
speed configurations. The speed of the fan directly relates to 
the amount of airflow. 

3.3.1

 

Variable Speed

Variable  speed  motor  control  allows  the  user  to  directly 
control the fan speed from the face of the unit. Turning the dial 
clockwise increases the speed, and counterclockwise slows the 
fan down. Turning the dial all the way  counterclockwise you 
will hear a click, which will turn the fan off, as well as the UVC 
light and Ionizer (if applicable). 

3.3.2

 

Constant Speed

Constant speed control allows the unit to run at a single speed 
when it is turned on, with no outside adjustment.  

Inside of the electrical chamber, there is a speed board which 
will  allow  the  user  to  turn  up  or  down  the  fan  speed  to  the 
desired set point. The speed board is controlled by turning the 
dial clockwise to increase and  counterclockwise to decrease. 
The  adjustment  can  be  done  with  a  small  slot  terminal 
screwdriver.  

Summary of Contents for Air Medic TIF-06













Reviews: