Tempest 396K Operation Manual Download Page 22

22 – 

English

FEDERAL EMISSION CONTROL WARRANTY STATEMENT

´®z+R4•¶53¨

´®z+R4•¶53¨

YOUR WARRANTY RIGHTS AND 
OBLIGATIONS

The EPA (The US Environmental Protection Agency), 
Environment Canada and Husqvarna Construction Products 
are pleased to explain the emissions control system warranty 
on your 2001 and later small nonroad engine. In U.S. and 
Canada, new small nonroad engines must be designed, built 
and equipped to meet the federal stringent anti-smog 
standards. Husqvarna Construction Products must warrant 
the emission control system on your small nonroad engine for 
the period of time listed below provided there has been no 
abuse, neglect or improper maintenance of your unit. Your 
emmission control system includes Parts such as the 
carburetor and the ignition system. Where a warrantable 
condition exists, Husqvarna Construction Products will repair 
your small nonroad engine at no cost to you. Expenses 
covered under warranty include diagnosis, parts and labor.

MANUFACTURER

′′′′

S WARRANTY 

COVERAGE

The 2001 and later small nonroad engines are warranted for 
two years. If any emission related part on you engine (as 
listed above) is defective, the part will be repaired or replaced 
by Husqvarna Construction Products.

OWNER

′′′′

S WARRANTY RESPONSIBILITIES

As the small nonroad engine owner, you are responsible for 
the performance of the required maintenance listed in your 
Operator

s Manual. Husqvarna Construction Products 

recommends that you retain all receipts covering maintenance 
on your small nonroad engine, but Husqvarna Construction 
Products cannot deny warranty solely for the lack of receipts 
or for your failure to ensure the performance of all scheduled 
maintenance. As the small nonroad engine owner, you should, 
however, be aware that Husqvarna Construction Products 
may deny you warranty coverage if your small nonroad engine 
or a part of it has failed due to abuse, neglect, improper 
maintenance, unapproved modifications or the use of parts 
not made or approved by the original equipment manufacturer. 
You are responsible for presenting your small nonroad engine 
to a Husqvarna Construction Products authorized servicing 
dealer as soon as a problem exists. The warranty repairs 
should be completed in a reasonable amount of time, not to 
exceed 30 days. If you have any questions regarding your 
warranty rights and responsibilities, you should contact your 
nearest authorized servicing dealer or call Husqvarna 
Construction Products, at 1-800-323 3553.

WARRANTY COMMENCEMENT DATE

The warranty period begins on the date small nonroad engine 
is delivered.

LENGTH OF COVERAGE

Husqvarna Construction Products warrants to the initial 
owner and each subsequent purchaser that the engine is free 
from defects in materials and workmanship which cause the 
failure of a warranted part for a period of two years.

WHAT IS COVERED

REPAIR OR REPLACEMENT OF PARTS

 Repair or 

replacement of any warranted part will be performed at no 
charge to the owner at an approved Husqvarna Construction 
Products servicing dealer. If you have any questions 

regarding your warranty rights and responsibilities, you 
should contact your nearest authorized servicing dealer or 
call Husqvarna Construction Products, at 1-800-323 3553.

WARRANTY PERIOD

 Any warranted part which is not 

scheduled for replacement as required maintenance, or which 
is scheduled only for regular inspection to the effect of “repair 
or replace as necessary” shall be warranted for 2 years. Any 
warranted part which is scheduled for replacement as 
required maintenance shall be warranted for the period of 
time up to the first scheduled replacement point for that part.

DIAGNOSIS

 The owner shall not be charged for diagnostic 

labor which leads to the determination that a warranted part 
is defective, if the diagnostic work is performed at an 
approved Husqvarna Construction Products servicing dealer.

CONSEQUENTIAL DAMAGES

 Husqvarna Construction 

Products may be liable for damages to other engine 
components caused by the failure of a warranted part still 
under warranty.

WHAT IS NOT COVERED

All failures caused by abuse, neglect or improper 
maintenance are not covered.

ADD -ON OR MODIFIED PARTS

The use of add-on or modified parts can be grounds for 
disallowing a warranty claim. Husqvarna Construction 
Products is not liable to cover failures of warranted parts 
caused by the use of add-on or modified parts.

HOW TO FILE A CLAIM

If you have any questions regarding your warranty rights and 
responsibilities, you should contact your nearest authorized 
servicing dealer or call Husqvarna Construction Products, at 
1-800-323 3553.

WHERE TO GET WARRANTY SERVICE

Warranty services or repairs shall be provided at all 
Husqvarna Construction Products authorized servicing 
dealers.

MAINTENANCE, REPLACEMENT AND 
REPAIR OF EMISSION-RELATED PARTS

Any Husqvarna Construction Products approved replacement 
part used in the performance of any warranty maintenance or 
repairs on emission-related parts, will be provided without 
charge to the owner if the part is under warranty.

EMISSION CONTROL WARRANTY PARTS 
LIST

1

Carburetor and internal parts

2

Intake pipe, airfilter holder and carburetor bolts.

3

Airfilter and fuelfilter covered up to maintenance schedule.

4

Ignition System 

1

Spark Plug, covered up to maintenance schedule

2

Ignition Module

MAINTENANCE STATEMENT

The owner is responsible for the performance of all required 
maintenance, as defined in the operator’s manual.

Summary of Contents for 396K
























Reviews: