background image

14 – 

English

FUEL HANDLING

Fuel

CAUTION! The machine is equipped with a two-stroke engine 
and must always been run using a mixture of gasoline and 
two-stroke engine oil. It is important to accurately measure 
the amount of oil to be mixed to ensure that the correct 
mixture is obtained. When mixing small amounts of fuel, even 
small inaccuracies can drastically affect the ratio of the 
mixture.

Gasoline

The lowest recommended octane grade is 87 
((RON+MON)/2). If you run the engine on a lower octane 
grade than 87 so-called knocking can occur. This gives 
rise to a high engine temperature and increased bearing 
load, which can result in serious engine damage.

Two-stroke oil

For best results and performance use HUSQVARNA two-
stroke engine oil, which is specially formulated for our air-
cooled two stroke-engines.

Never use two-stroke oil intended for water-cooled 
engines, sometimes referred to as outboard oil (rated 
TCW).

Never use oil intended for four-stroke engines.

Mixing ratio

1:50 (2%) for all engines.

Mixing

Always mix the gasoline and oil in a clean container 
intended for fuel.

Always start by filling half the amount of the gasoline to be 
used. Then add the entire amount of oil. Mix (shake) the 
fuel mixture. Add the remaining amount of gasoline.

Mix (shake) the fuel mixture thoroughly before filling the 
machine’s fuel tank.

Do not mix more than one month’s supply of fuel at a time.

If the machine is not used for some time the fuel tank 
should be emptied and cleaned.

Fueling

Keep the handle dry and free from oil and fuel.

Ensure that the fuel is well mixed by shaking the container 
before filling the tank.

Always exercise care when refilling the fuel. Move the 
machine at least three metres from the fuelling area 
before it is started. Check that the fuel cap is tightened 
correctly.

Clean around the fuel cap. Clean the fuel and oil tank 
regularly. The fuel filter should be changed at least once a 
year. Contamination in the tanks causes malfunction.

!

WARNING! Always ensure there is adequate 
ventilation when handling fuel.

Gasoline, litre

Two-stroke oil, litre

2% (1:50)

5

0,10

10

0,20

15

0,30

20

0,40

US gallon

US fl. oz.

1

2 1/2

2 1/2

6 1/2

5

12 7/8

!

WARNING! Taking the following precautions, 
will lessen the risk of fire:

Do not smoke or place hot objects near fuel.

Always shut off the engine before refuelling.

When refuelling, open the fuel cap slowly so 
that any excess pressure is released gently.

Tighten the fuel cap carefully after refuelling.

Always move the machine away from the 
refuelling area before starting.

Summary of Contents for 396K
























Reviews: