background image

English

 – 13

ASSEMBLY

Checking the drive axle and flange 
washers

Check that the threads on the drive shaft are undamaged.

Check that the contact surfaces of the cutting blade and 
flanges are flat, run correctly on the spindle and are free from 
foreign objects.

Do not use warped, notched, indented or dirty flange 
washers. Do not use different dimensions of flange washers.

Fitting the cutting blade

Husqvarna cutting blades are manufactured and approved for 
freehand cutting. The paper labels on each side of the blade 
are there to distribute the pressure from the flange washer 
and prevent the blade from slipping.

The blade is placed on the bushing between the inner flange 
washer (A) and the flange washer (B). The flange washer is 
turned so that it fits on the axle.

The shaft can be locked using a screwdriver, steel pin or the 
like. This is slid in as far as possible. The blade is tightened 
clockwise.

Tightening torque for the bolt holding the blade is: 15-25 Nm 
(130-215 in.lb).

Guard for the blade

The guard must always be fitted on the machine. The guard 
for the cutting equipment should be adjusted so that the rear 
section is flush with the work piece. Spatter and sparks from 
the material being cut are then collected up by the guard and 
led away from the user.

!

WARNING! A 16 inch blade guard should 
only be used on power cutters initially 
equipped with a 16 inch blade guard. If a 
guard obtained as a spare part is fitted on a 
power cutter which is equipped with a 12 or 
14 inch guard, a 16 inch blade will run too 
fast. A cutting blade running at a too high 
speed can break or cause serious damage.

Summary of Contents for 396K
























Reviews: