background image

USING YOUR FIREPLACE 

1. Open the firescreen by grasping the handles and pushing 

them back to each side. 

2. The flue damper rod is located behind the mesh screens.  

To open the damper, slide the rod to the right.  To close, 
slide the rod to the left. 

3. If the combustion air kit has been installed, the inlet air 

damper should be in a fully open position before you start 
a fire.  Reach behind the screen and release the control 
rod on the front of the left side of the firebox. To open, 
turn the control until it is pointing down. To close the 
damper, rotate the control rod counterclockwise until it is 
pointing to the three o'clock position.  The control rod will 
lock in the closed position and swing free in the open position. 

4. A TEMCO fireplace grate must be used in this fireplace.  It is 

pre-installed at the factory as an integral part of the fireplace. 

5. Light a piece of crumpled paper and hold it high inside 

the fireplace. This will warm the flue and start the 
chimney "drawing". 

6. Light the paper in the grate and add kindling.  As the 

kindling catches, add more or heavier wood until the fire 
is well established.  Be careful not to "smother" the fire. 

7. WARNING: NEVER USE GASOLINE, GASOLINE-TYPE 

LANTERN FUEL, KEROSENE, CHARCOAL LIGHTER 
FLUID OR SIMILAR LIQUIDS TO START OR FRESHEN UP 
A FIRE IN THIS FIREPLACE.  KEEP ALL SUCH LIQUIDS 
WELL AWAY FROM THE FIREPLACE WHILE IT IS IN USE. 

8. Close the right firescreen first and then the left firescreen, 

being sure that they overlap.  Keep the firescreens 
closed at all times except when adding fuel. 

9. Ashes that build up from burning logs must be removed 

periodically to allow space for air to move under and up 
through the fuel for combustion.  If these ashes are 
allowed to accumulate until the air flow is blocked, the 
grate may become badly warped from excessive heat. 

10.A fireplace needs a steady supply of air in order to draw 

properly.  Many houses or apartments which are well 
sealed lack sufficient air for normal operation.  Ventilating 
fans, exhaust hoods or central heating systems often 
cause fireplaces to smoke by stealing the fireplace's 
combustion air.  If the volume is enough, it can reverse 
the flow of air in the fireplace and cause smoking. 

11.Use solid wood for fuel.  Use dry and well seasoned 

wood.  Do not burn scrap  construction lumber; it 
produces excessive sparks.  Never use woods dipped in 
tar, pitch, creosote, etc. as this produces sputtering, 
smoking fires with toxic fumes.  Do not use wood 
products with synthetic binders like plywood or artificial 
logs as these  produce abnormally high temperatures 
and may cause deterioration of chimney material. 

12.DO NOT OVER-FIRE WITH EXCESSIVE FUEL LOADS 

SUCH AS LUMBER, WRAPPING PAPER, CHRISTMAS 
TREES, ETC.  THE FIREPLACE IS OVER-FIRED IF THE 
TOP OF THE FLAMES ARE GOING UP INTO  THE 
CHIMNEY OR LICKING OUT OF THE FIREBOX. 

?

OVER-FIRING WITH THE GLASS DOORS IN THE 
CLOSED POSITION CAN CAUSE THE GLASS TO 
SHATTER RESULTING IN PROPERTY DAMAGE AND/OR 
PERSONAL INJURY.  TEMCO DOES NOT WARRANT 
THE GLASS AND IS NOT RESPONSIBLE FOR 
CONSEQUENTIAL PROPERTY DAMAGE AS STATED IN 
THE SEPARATE GLASS DOOR WARRANTY. 

 
 
 

13.Creosote Formation and Need for Removal:

  When 

wood is burned slowly, it produces tar and other organic 
vapors which combine with expelled moisture to form 
creosote.  The creosote vapors condense in the relatively 
cool chimney flue of a slow-burning fire.  As a result, 
creosote residue accumulates on the flue  lining.  If 
ignited, this creosote makes an extremely hot fire.  The 
chimney should be inspected at least twice a year during 
the heating season to determine if a creosote buildup has 
occurred.  If creosote has accumulated, it should be 
removed to reduce the risk of a chimney fire.

 

14.CHARCOAL AND COAL MAY NOT BE BURNED IN 

THIS FIREPLACE.  

15.NEVER CLOSE ANY DAMPERS UNTIL YOU ARE 

CERTAIN THAT THERE ARE NO WARM EMBERS. 

16.When the fire has gone completely out, close all 

dampers.  This will prevent excessive heat loss up the 
chimney and excessive water on the hearth.  If a 
combustion air kit is installed, close the inlet air damper. 

17.The brick-like refractory on the floor, back and sides is 

reinforced with steel but can be cracked and broken.  Don't 
drop logs or build fires directly against refractories.  A careful 
"burn-in" of your fireplace is recommended during initial use.  
For the first few fires, build modest fires.  This will cure the 
refractories properly.  Hairline cracks may appear in the 
refractories but do no harm to their performance. 

18.It is important for the chimney to be high enough to draw 

properly.  The chimney should extend 3' above the highest 
point where it passes through the roof and 2' above any 
portion of the roof horizontally within 10'.  See pages 9 and 
10. 

19.Disposal of Ashes:

  Ashes should be placed in a metal 

container with a tight fitting lid.  The closed container of 
ashes should be placed on a noncombustible floor or on the 
ground, well away from all combustible materials, pending 
final disposal.  If the ashes are disposed of by burial in soil or 
otherwise locally dispersed, they should be retained in the 
closed conta iner until all cinders have thoroughly cooled.

 

20.WARNING:   Any accessory component(s) used with 

this fireplace other than those specified, must be 
listed or approved by a nationally recognized 
certification agency for the application and be 
installed and  used in accordance with the accessory 
manufacturer’s instructions and local codes. 

21.Access to chimney for cleaning:  

To remove the 

termination cap, remove the three #10A x 7 hex-head 
screws from the termination brackets.  Grasp the skirt 
with one hand on each side and pull up.  To replace the 
cap, reposition the termination cap on the chimney pipe 
and align the termination brackets with the holes in the 
pipe.  Securely attach the termination cap to the chimney 
with the three screws removed earlier.

 

22.WARNING:  FIREPLACES EQUIPPED WITH DOORS 

SHOULD BE OPERATED ONLY WITH DOORS FULLY 
OPEN OR DOORS FULLY CLOSED.  IF DOORS ARE 
LEFT PARTLY OPEN, GAS AND FLAME MAY BE 
DRAWN OUT OF THE FIREPLACE OPENING, 
CREATING RISKS OF BOTH FIRE AND SMOKE. 

23.Keep all combustibles such as furniture, draperies, 

papers and stored wood away from the front of the 
fireplace. 

15 

Summary of Contents for TLC36-3M





















Reviews: