background image

19 

LIMITED WARRANTY AND EXCLUSIONS 

For TEMCO Low Profile, Front-Opening, Wood Burning Fireplaces 

Models TLC42-4, TLC42-4I, TLC42-4MB, TFC42-4, TLC3922, TLC39-3, TLC39-3I, TFC39-3, TLC36-

3, TLC36-3I, TLC36-3MB, TFC36-3, A42L-4, A42F-4, A39L-3, A39F-3, A36L-3 AND A36F-1

 

 

This Limited Warranty covers the above described fireplace and chimney systems.  Accessories such as glass 
doors, combustion air kits and fans are covered in separate warranties. 

The First Year of Coverage 

During the first year after installation, 

TEMCO Fireplace Products, Inc

.  will at its option repair or replace any 

defective part of the fireplace or chimney system or refund to the original owner a sum of money not to exceed the 
suggested retail price of the system at the time of purchase.  The date of installation must be verified by 
acceptable proof of purchase, canceled check or recorded and dated deed to the property where the system is 
installed.  
 

The Second Through Fifth Years of Coverage 

From the second through the fifth year after installation, 

TEMCO

  will make available to the original owner, at no 

charge, at its factory a replacement for any defective part in the fireplace or chimney system except for refractories 
or grates.  Defective refractories and grates can be replaced by the original owner at 

TEMCO’s

  factory at fifty 

percent (50%) of the current list price from the second through the fifth years after installation.  
 

The Sixth Through the Tenth Years of Coverage 

From the sixth through the tenth years after installation.  

TEMCO Fireplace Products

 will make available to the 

original owner at fifty percent (50%) of the current suggested list price at its factory a replacement for any defective 
part in the fireplace or chimney system except for refractories and grates which may be replaced at full list price.  
Some states do not allow limitations on how long an implied warranty lasts so the above limitations may not apply 
to all consumers.

 

 

What is Not Covered 

This warranty does not cover any cost or expenses not herein set forth as being the responsibility of 

TEMCO 

Fireplace Products

 and specifically does not cover the following:  

Anyone other than the original owner.  

Shipping costs after the first year of coverage. 

Labor after the first year of coverage.  

Damage caused by improper installation, misuse, abuse or alteration of the fireplace or chimney system. 

Cracks in refractories that do not affect safe operation.  

Any work done or cost incurred without written consent from TEMCO Fireplace Products. 

Installation performed by  unlicensed or unqualified agent per NFPA  211.  

 

Limitations and Exclusions 

1.

TEMCO Fireplace Products

 authorizes no one to add to or alter this Limited Warranty.

 

2.

TEMCO Fireplace Products

 is not liable for incidental, consequential, special or contingent damages.  Some 

states do not allow exclusion or limitation of incidental or consequential damages, so the above limitation or 
exclusion may not apply to all consumers.

 

3.

This Limited Warranty applies only to the original owner of the fireplace and  chimney system with the model 
number described above or the original owner of the dwelling in which one of the above described fireplace 
and chimney systems is installed. 

4.

Removal of fireplace from original installation site voids warranty. 

5.

TEMCO Fireplace Products

 reserves the right to investigate any or all claims against this warranty.

 

 

Owner’s Duties 

The fireplace and chimney to which this Limited Warranty applies must be installed and used in strict compliance 
with 

TEMCO

 

Fireplace Products

 installation manual.  Failure to do so will void this warranty.  If you have a 

problem with your fireplace, first consult the installation manual to insure that your system has been properly 
installed and is being used in accordance with the manual.  After doing so, if you still have a problem, contact the 
nearest 

TEMCO

 dealer or distributor.  If necessary, you may find out the name of your nearest dealer or distributor 

by writing 

TEMCO

 Fireplace Products and requesting such information.  Upon notification of your problem, a 

representative of the dealer or distributor will inspect your fireplace.  A determination will be made whether or not  
your problem is covered under this Limited Warranty, and you will be contacted.  
 
This Limited Warranty is given in lieu of any other expressed or implied warranties. 

Summary of Contents for TFC39-22





















Reviews: