Telit Wireless Solutions M.2 HN930, Hardware User'S Manual

Page: 57 / 77

xN930 M.2 Hardware User Guide
1VV0301078 Rev.6 – 2013-11-12
8.2 Electrical Parameters - Host Interface Signals
Table 26 Electrical Parameters – Host Interface Signals
Signal Pin Description I/O Voltage
Domain
(V)
DC Characteristics (V)
Min Typ Max
(VDD_IO
)
Card_Power_ON_OFF 6 Power On/Off M.2
Module
I 1.8 -0.3 0/1.8 2.3
RESET# 67 Reset M.2
Module
I 1.8 -0.3 0/1.8 2.3
LED#1 10 M.2 Status
Indicator
O (OD) 3 Open-Drain Output, Host
requires pull-up resistor
W_DISABLE# 8 M.2 Disable I 1.8 -0.3 1.8 2.1
WAKE_WWAN# 23 WWAN wake Host O 1.8 -0.3 0/1.8 2.4
DPR# 25 Body SAR Detection I 1.8 -0.3 0/1.8 2.1
USB ( D+/D-) 7,
9
USB D+/D- 2.0
High-speed
I/O 1.8/2.9 -0.3 1.8/2.9 V
DDIO
+0.3
SIM_DETECT 66 SIM Card Detection I 1.8/2.9 -0.3 1.8/2.9 V
DDIO
+0.3
UIM_CLK 32 SIM Card Clock O 1.8/2.9 -0.3 1.8/2.9 V
DDIO
+0.3
UIM_RESET 30 SIM Card Reset O 1.8 /2.9 -0.3 1.8/2.9 V
DDIO
+0.3
UIM_DATA 34 Sim Card DATA I/O 1.8/2.9 -0.3 1.8/2.9 V
DDIO
+0.3
UIM_PWR 36 SIM Card Power O 1.8/2.9 -0.3 1.8/2.9 V
DDIO
+0.3
I2C_SCL 40 GNSS – I2C Clock I/O 1.8 -0.3 0/1.8 2.1
I2C_SDA 42 GNSS – I2C Data I/O 1.8 -0.3 0/1.8 2.1
I2C_IRQ 44 GNSS – I2C Interrupt I 1.8 -0.3 0/1.8 2.1
CLKOUT0 46 GNSS – 26 MHz Clock
Synchronization
O 1.8 -0.3 0/1.8 2.1
TX_BLANKING 48 GNSS – TX Blanking O 1.8 -0.3 0/1.8 2.1
GNSS_DISABLE# 26 Disable GNSS I 1.8 -0.3 0/1.8 2.1
ANTCTL[3:0] 59,
61,
63,
65
Antenna Tuning
Signals
– RF Engine
O 2.3 -0.3 2.3 3.3
COEX[3:1] 60,
62,
64
RF Coexistence
Synchronization
I/O 1.8 -0.3 0/1.8 2.1
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 57 of 77