manualshive.com logo in svg

Telit Wireless Solutions HE910-EU V2, Hardware User'S Manual

Share
Download
Telit Wireless Solutions HE910-EU V2 Hardware User'S Manual Download Page 9

 
 

 

 

 

 

 

 

The aim of this document is the description of some hardware solutions useful for developing 
a  product  with the  Telit  HE910-EU/EUG  V2  HE910-NA/NAG  V2  module.  All  the  features 
and solutions detailed are applicable to all HE910 V2, whereas “HE910 V2” is intended the 
modules listed in the applicability table. 

When a specific feature is applicable to a specific product, it will be clearly highlighted. 

 

This document is intended for Telit customers who are about to implement their applications 
using our HE910 V2 modules. 

 

For general contact, technical support, to report documentation errors and to order manuals, 
contact Telit Technical Support Center (TTSC) at: 

 

[email protected] 
[email protected]

 

[email protected] 
[email protected] 

 

Alternatively, use:  

http://www.telit.com/en/products/technical-support-center/contact.php

 

For  detailed  information  about  where  to  buy  the  Telit  modules  or  for  recommendations  on 
accessories and components visit:  

http://www.telit.com

 

To  register  for  product  news  and  announcements  or  for  product  questions  contact  Telit 
Technical Support Center (TTSC). 

Our aim is to make this guide as helpful as possible. Please keep us informed of comments 
and suggestions for improvements. 

Telit appreciates feedback from the users of our information. 

Summary of Contents for HE910-EU V2















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands