manualshive.com logo in svg

Telit Wireless Solutions HE910-EU V2, Hardware User'S Manual

Share
Download
Telit Wireless Solutions HE910-EU V2 Hardware User'S Manual Download Page 75

 
 

 

 

 

 

 

 

Modification statement

 

 
Telit has not approved any changes or modifications to this device by the user. Any changes or modifications 
could void the user’s authority to operate the equipment. 
 

Telit n’approuve aucune modification apportée à l’appareil par l’utilisateur, quelle qu’en soit la nature. Tout 
changement ou modification peuvent annuler le droit d’utilisation de l’appareil par l’utilisateur.

 

 

Interference statement 
 

This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s). 
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this 
device must accept any interference, including interference that may cause undesired operation of the device. 
This Class B digital apparatus complies with Canadian ICES-0003.

 

 

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de 
licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de 
brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le 
brouillage est susceptible d'en compromettre le fonctionnement.

 

 

Wireless notice 
 

This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. 
The antenna should be installed and operated with minimum distance of 20 cm between the radiator and your 
body. Antenna gain must be below:

 

 

Frequency band

 

HE910-NA V2 

HE910-NAG V2 

GSM/GPRS850 

7.43 dBi 

7.43 dBi 

FDD V 

8.45 dBi 

8.45 dBi 

GSM/GPRS1900 / FDD II 

3.0 dBi 

3.0 dBi 

 
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 
 

Cet appareil est conforme aux limites d'exposition aux rayonnements de la IC pour un environnement non 
contrôlé. L'antenne doit être installé de façon à garder une distance minimale de 20 centimètres entre la 
source de rayonnements et votre corps. Gain de l'antenne doit être ci-dessous: 
 

Bande de fréquence

 

HE910-NA V2 

HE910-NAG V2 

GSM/GPRS850 

7.43 dBi 

7.43 dBi 

FDD V 

8.45 dBi 

8.45 dBi 

GSM/GPRS1900 / FDD II 

3.0 dBi 

3.0 dBi 

 
L'émetteur ne doit pas être colocalisé ni fonctionner conjointement avec à autre antenne ou autre émetteur. 
 

Summary of Contents for HE910-EU V2















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands