manualshive.com logo in svg

Telit Wireless Solutions BlueMod+S42/AI, Hardware User'S Manual

Share
Download
Telit Wireless Solutions BlueMod+S42/AI Hardware User'S Manual Download Page 54

 
 

 

S42 Hardware User Guide 

1VV0301303 Rev.3 – 2016-08-22  

Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved.
 

 

Page 54 of 62

 

this device must accept any interference received, including interference that may cause 
undesired operation. 

 

8.2.3 

FCC Caution 

 

WARNING: 

Changes or modifications made to this equipment not expressly approved by Telit may void 
the FCC authorization to operate this equipment. 

 

8.2.4 

FCC Warning 

This equipment has been tested and found to comply with the limits for a Class B digital 
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference in a residential installation. This equipment generates, 
uses and can radiate radio frequency energy and, if not installed and used in accordance with 
the instructions, may cause harmful interference to radio communications. However, there is 
no guarantee that interference will not occur in a particular installation. If this equipment does 
cause harmful interference to radio or television reception, which can be determined by 
turning the equipment off and on, the user is encouraged to try to correct the interference by 
one or more of the following measures: 

Reorient or relocate the receiving antenna. 

Increase the separation between the equipment and receiver. 

Connect the equipment into an outlet on a circuit different from that to which the receiver is 
connected. 

Consult the dealer or an experienced radio/TV technician for help. 

8.2.5 

FCC RF-exposure Statement 

The S42/AI complies with the FCC/IC RF radiation exposure limits set forth for an 
uncontrolled environment.  

The output power is < 10mW 

EIRP

 and therefore according to “FCC KDB 447498 D01 

General RF Exposure Guidance v05” Appendix A, table “SAR Exclusion Threshold”, 
excluded from SAR testing for test separation distances 

≥ 5mm and if it is not used in co-

locations with other antennas. If the product implementing the S42/AI has other 
antennas in co-location or separation distances < 5mm an FCC TCB should be asked for a 
Class II Permissive Change. 

 

Summary of Contents for BlueMod+S42/AI































































Reviews:

No comments

Brands by name

Popular brands

Load more brands