5
The last 4 digits of the IMEI are therefore the password for your device and should be kept secretly from your side.
The IMEI number cannot be changed! You can also change the password for security relevant cases, but please
bare in mind that each command – also the reset to the factory status- will presumes the knowledge of this
password.
Control Commands via SMS:
Control commands via SMS will only be executed, if the phone number of the sender has been communicated to
the STD35 before. Control commands
don’t need
a password.
All command (with exception of R: and ST?) have to be terminated with a dot!
All commands can be sent in one SMS, separated one from the other by the terminating dot.
The indications of the seconds can have 1-5 digits. Valid indications are e.g.: 1 or 90 or 99999, that means there
won’t be put leading Zeros before the digits (e.g. “O1:90”. This is euiqvalent of 90 seconds).
Please pay attention to the difference between the number 0 and the letter O! (“O1ON.” Contains two times
the letter O, whereas “O1:0” contains once the letter O and once the number 0).
Basic functions
•
After having been called from the assigned („stored“, pls. See configuration call) mobile phone, the relay 1
switches for a second.
•
When the digital input1 will be activated for a second, the STD35 sends a SMS with the content „EVENT
ALARM 1“ to the assigned mobile phone.
•
When the digital input2 will be activated for a second, the STD35 sends a SMS with the content „EVENT
ALARM 2“ to the assigned mobile phone.
•
The same is certainly valid for the inputs 3 to 5.
Switching via SMS
•
After having received a SMS with the content „O1ON.“ (=Output 1 ON) from the assigned mobile phone, the
relay 1 will switch for a second. In case of a SMS “O2ON.” The relay 2 will switch for a second.
•
The same is certainly valid as well for the outputs “relay 3 to relay 5”.
•
In the case that the switching time has been put to 0 (number 0), the relays switch permanently to the other
status.
Configuration SMS
•
The configuration SMS is valid, only if beginning with the 4 digit password. Teh CLIP of each of the
configuration SMS will, if the password is correct, be logged automatically as a new administrator. Therefore it
has to be considered, that the configuration only is executed from the mobile phone of the administrator.
•
With a SMS having the content „O1:xxxxx.“ (character O= (xxxxx = seconds) the switching times of the relays
can be configured. The STD35 will keep these configurations even after the cut-off from the supply voltage.
•
In case that the switching time for a relay has been put to 0, the STD35 will, at each new call, switch the related
relay permanently. Has the relay been active before, it will go to inactive and vice versa.
In this case also a SMS containing “O1ON.” from the assigned mobile phone will switch the relay 1 on
permanently. A SMS with the content “O1OFF.” will then switch the relay 1 again off permanently. Accordingly
the relays 2 to 5 will react on SMS messages which contain “OxON.” And “OxOFF.” (x=2...5).
•
By a SMS with the content e.g. “I1:xxx.” (xxx=seconds) the times can be programmed for the five inputs, during
which these inputs have to be active, before the STD35 will send out an alarm SMS.
The inputs 2 to 5 show the identical behavior.
•
By a SMS with the content e.g. “V1:x.” Or “V2:x.” (x = 1 oder 0) the polarity of the inputs can be inverted. In
case of x=1 there will be sent a alarm SMS, if the input was deactivated longer then the configured time. For
the inputs 3 to 5 equivalent proceeding is valid (e.g. V4:x.).
