background image

DVB-T Modulator

12

10) Network 

This interface indicates the default IP address and network mask of this device. 

User can revise it and click “Apply” to confirm.

11) Password 

User can revise the login password in this menu by type accordingly information 

as required and click “Apply” to confirm.

 

6. Troubleshooting 

Televés’  ISO9001  quality  assurance  system  has  been  approved  by  CQC 

organization.  For  guarantee  the  products’  quality,  reliability  and  stability.  All 

Televés products have been passed the testing and inspection before ship out 

factory. 

The testing and inspection scheme already covers all the Optical, Electronic and 

Mechanical criteria which have been published by Televés. To prevent potential 

hazard, please strictly follow the operation conditions. 

Prevention Measure 

  Installing the device at the place in which environment temperature between 

0 to 45 °C 

  Making sure good ventilation for the heat-sink on the rear panel and other 

heat-sink bores if necessary 

  Checking  the  input  AC  within  the  power  supply  working  range  and  the 

connection is correct before switching on device 

  Checking the RF output level varies within tolerant range if it is necessary 

  Checking all signal cables have been properly connected 

  Frequently switching on/off device is prohibited; the interval between every 

switching on/off must greater than 10 seconds. 

Conditions need to unplug power cord 

  Power cord or socket damaged. 

  Any liquid flowed into device. 

  Any stuff causes circuit short 

  Device in damp environment 

  Device was suffered from physical damage 

  Longtime idle. 

  After switching on and restoring to factory setting, device still cannot work 

properly. 

  Maintenance needed

7. Application 

7.1 Ordering guideline 

Our  design  is  individual  module,  for  this  series  device  the  encoding  module 

including three version for optional:

  MPEG2 SD encoding with 1 CVBS module 

  MPEG2 SD super encoding with 2 CVBS module 

  MPEG4 AVC H.264 encoding with 1 HDMI module 

Modulation module including one version for optional:

  DVB-T COFDM RF out module 

Summary of Contents for 554501





















Reviews: