Teledyne Q-Flex Page 85 Installation And Operating Handbook Download | Manualshive

Page: 85 / 234

background image

Q-Flex Satellite Modem Installation and Operating Handbook

6-55

6.2.2.13 MPE MAC Address

Format
example:

00:11:29:00:F0:23

Description:

For  DVB-S2  IP  services,  this  is  used  for  filtering  of  Multi-Protocol
Encapsulation  (MPE)  packets  on  the  receive  side.  The  receiver  will  filter
against  whatever  MAC  address  has  been  provided,  which  can  therefore
be a virtual MAC address rather than the receiver’s address.

(There  is  currently  no  equivalent  modulator  support  to  allow  a  specific
MAC  address  to  be  added  to  MPE  packets.  A  Paradise  modulator  will
always set the MPE MAC address to all zeros in routing mode and to the
destination MAC address of the incoming Ethernet frame when in bridging
mode.)

Table 6-59 MPE MAC Address

6.2.2.14 Weighted QoS

This is an On/Off control that controls IEEE 802.1p packet prioritization. It is mutually
exclusive with the traffic shaping feature and when traffic shaping is enabled then
strict/fair queuing will be automatically switched off.

This allows for eight classes of data to be specified as part of a three-bit field within the
Layer 2 IEEE 802.1q VLAN header. The packets must already be tagged at the point of
entry to the modem. Priority 7 is typically used for network-critical traffic such as dynamic
routing protocol packets; priorities 5 and 6 for video and voice, etc. The modem uses the
priority tag to decide how to process each packet. The options are:

•

Strict-priority queuing

: packets are queued for transmission based solely on

their priority with the highest always being sent first. Strict-priority queuing is
active whenever

Weighted QoS

is set to Off.

•

Fair-weighting queuing

: higher-priority packets are transmitted first but

lower-priority packets are given a percentage of the bandwidth. Fair-weighting
queuing is active whenever

Weighted QoS

is set to On.

The implementation of IEEE 802.1p packet prioritization is as follows:

•

The eight QoS priority levels are mapped to three TCP/IP queues in the
modem.

•

Packets with highest QoS priority (level 7) are sent to high priority TCP/IP
queue.

•

Delay-sensitive packets (QoS levels 6 and 5) are sent to the medium priority
queue.

•

The remainder (QoS levels 4 to 0) are sent to the low priority TCP/IP queue.

•

For strict-priority queuing, all packets in the high-priority queue are processed
before any in the medium-priority queue, which in turn are processed before
any in the low-priority queue.

«
...
83
84
85
86
87
...
»

Summary of Contents for Q-Flex











































































































































































































































Reviews:

No comments

Related manuals for Q-Flex

Brand: T-Mobile Pages: 2

Brand: M/A-Com Pages: 22

RM356 - Router - EN

Brand: NETGEAR Pages: 2

Brand: CS Pages: 50

Brand: Intercel Pages: 7

Brand: Cyta Pages: 20

Brand: Linksys Pages: 24

Brand: YoungWoo Pages: 50

Brand: Data-Linc Group Pages: 15

Brand: Zoom Pages: 24

Brand: Huawei Pages: 59

Brand: Huawei Pages: 10

Brand: Huawei Pages: 16

Brand: Huawei Pages: 2

Brand: Huawei Pages: 3

Brand: Huawei Pages: 20

Brand: Huawei Pages: 5

Brand: Huawei Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands