manualshive.com logo in svg

Teledyne FST-040, Manual

Share
Download
Teledyne FST-040 Manual Download Page 3

 

Technical Note 

FST-040 (August 2011)

 Revised January 2012

 

 

FST-040 (August 2011) Revised January 2012 

page 3 of 21 

EAR-Controlled Technology Subject to Restrictions Contained on the Cover Page.

 

TELEDYNE

RD INSTRUM ENTS

A Teledyne Technologies Company

Configuring the Serial Connection to the Surface IMM 

To configure the serial connection to the surface IMM:  

1.  Connect and power up the DVS as shown in Figure 1. 
2.  Start the

 DVS 

software. 

3.  At the 

DVS Wizard Startup Options

 screen, click 

Cancel

.   

4.  From the 

Configure

 menu, click 

Serial Communications

. 

 

5.  Select the appropriate 

COM port 

(i.e. the port that the surface modem is con-

nected to). For the baud rate, select 9600.  Serial communications with the IMM’s 

should always be set to 9600 baud.  Leave the other settings at their default val-

ues. 

6.  Select the 

Using an Inductive Modem

 box and click the 

Get Modem ID

 button. 

7.  Press the 

OK

 button to close the 

Serial Communication Settings

 dialog. 

 

The inductive modems actually communicate with each other at a baud 

rate of 1200, and do not support communication with the DVS at baud 

rates above 9600. 

 

8.  On the 

Configure

 menu, select 

Modems

.  Select which modem(s) to configure 

(i.e. the Surface IMM connected to the serial port and/or the DVS IMM).  

Summary of Contents for FST-040






















Reviews:

No comments

Brands by name

Popular brands

Load more brands