background image

l

 

Never install telephone or Ethernet jacks in wet locations unless the jack is specially designed for wet 

locations. 

l

 

Never touch uninstalled telephone wires or terminals unless the telephone line has been         

disconnected at the network interface. 

l

 

Use caution when installing or modifying telephone and network lines. 

l

 

Be sure your power adaptor meets your regions requirements prior to installation. 

6.1 Connect power line cord 

Two line cords are provided 1-RJ45 & 1-RJ11. 

To install, simply plug one end of the

 

RJ45 cord into the modular jack at the top end of the base 

unit and the other end

 

into the RJ45 Phone Jack on the power adaptor. Take other line cord and plug

 

into Line jack on power adaptor, then plug other end into wall. Finish by plugging

 

power adaptor into 

normal wall outlet. 

Be sure your power adaptor is specified for your region of the world prior to plugging

 

into the wall 

socket. 

6.2 Battery for handset 

Charging the Handset Battery

: (On Base and Charging Station) 

The handset Battery is a Ni-MH battery. This battery requires a Full charge prior to use

 

to ensure long 

life. To charge the battery, complete the installation procedure by plugging

 

the power source into the 

wall outlet and the telephone base or charging station. 

Install the battery the battery per below instructions, inserting battery plug into receptacle. 
Place battery into opening in handset, press into place, then replace cover and place

 

handset into 

base (face down) or charging station (face down). 

Battery Life - When Completely Charged: 

Talk time:         7.5 hours 

Standby: (handset off hook) 6 days 
Charge for 24 hours to ensure a fully charged battery 

Installing Battery into Handset: 

1. Hands holding the handset and gently push up handset back shell, 
2. Take back shell off, exposing the battery compartment, 
3. Slide battery plug into receptacle, matching

 

up slot and opening on receptacle, 

4. Do not force battery. 
5. Press on back end of battery to snap into place. 
6. Put the back shell of handset into slot, then press down and snap into place. 
 

Summary of Contents for E103-DCX











Reviews: