manualshive.com logo in svg

Telect LTX, Installation Manual

Share
Download
Telect LTX Installation Manual Download Page 21

LTX Patch and Splice Panel

Installation Guide 

© Telect, Inc.  All rights reserved. 148326 12.20.16 v2

1.509.926.6000  ::  telect.com

21

3.1.10 Designation Label Installation

The installation instructions apply to the 

LTX 4RU, 2RU 

& 1RU

Refer to 

Figure 3-10, Figure 3-10-1 & Figure 3-10-2 

for this procedure.

Designation labels are used to identify adapter fiber 

jumper information at the front of the panel and 

 

connector pigtail fiber information at the rear of 

 

the panel. 

1.  Open the door to the front or rear of the LTX panel 

all the way so that the clear cover on the inside of 

the door is visible.

2.  Slide the designation label into the cover 

positioning it so that numbers can be read easily 

with the door open.

 

Designation label for the front of the LTX panel 

(fiber jumper adapter side) is marked "FRONT 

SIDE" on the bottom corner.

 

Designation label for the rear of the LTX panel 

(pigtail fiber connector side) is marked "REAR 

SIDE" on the bottom corner.

 

NOTE:  After installing both designation labels, 

ensure they are installed on the correct side of the 

LTX panel.

 

* Designation label for the 1RU is located on the 

front tray platform.

LTX 4RUPanel 

Clear Cover for  

Designation Label

Door

Figure 3-10 4RU Designation Label Installation

Door 

Clear Cover for

Designation Label

Figure 3-10-1 2RU Designation Label Installation

Figure 3-10-2 1RU Designation Label

 

Installation

Clear Cover for 

Designation Label

Tray

LTX 2RU Panel

LTX 1RU Panel

Summary of Contents for LTX




































Reviews:

No comments

Brands by name

Popular brands

Load more brands