manualshive.com logo in svg

Telect LTX, Installation Manual

Share
Download
Telect LTX Installation Manual Download Page 15

LTX Patch and Splice Panel

Installation Guide 

© Telect, Inc.  All rights reserved. 148326 12.20.16 v2

1.509.926.6000  ::  telect.com

15

3.1.4 Tray Platform Installation

The installation instructions apply to the 

LTX 4RU

Refer to 

Figure 3-4

 for this procedure.

The tray platform sits in the bottom center of the rear 

portion of the LTX panel. The platform contains routing 

spools, tray banding, tie-down slots and splice trays. 

The tray platform can be rotated out from inside the 

LTX panel or can be removed for splicing. 

1.  Position the tray platform on the bottom of the LTX 

panel in the rear portion of the tray. Center the 

platform tray between the sidewalls. Screw holes 

for the tray are near rear door hinges.

2.  Align the two thumb screw holes in the platform 

tray with the screw holes in the bottom of 

 

the panel.  

 

NOTE: It is recommended that routing spools, 

splice tray bands and empty splice trays are 

 

pre-installed before the tray platform is installed 

 

in the panel.

3.  Insert thumb screws through the top of the tray 

platform into the screw holes in the panel bottom.

4.  Rotate screws to tighten. Loosening one of the 

screws allows the tray platform to rotate out from 

inside the panel when needed.

Figure 3-4 4RU Tray Platform Installation

 

3.1.5 Cable Clamp Bracket Installation

The installation instructions apply to the 

LTX 4RU

Refer to 

Figure 3-5

 for this procedure.

Incoming cables route from above or below and enter the 

LTX panel at one of the upper rear corners. The cable 

clamp bracket is used to house the cable clamp which 

secures the cable to the panel.

1.  Position cable clamp bracket with the straight side 

up and the angled side facing down on the outside 

upper corner edge at the rear of the LTX Panel. 

2.  Align the two screw holes in the top portion of the 

bracket with the screw holes at the top edge of the 

rear overhang on the LTX panel.

3.  Insert two Phillips screws through the bracket from 

the outside into the panel edge screw holes 

 

and tighten.

Upper Rear 

Corner

Two 

Screws

Figure 3-5 4RU Cable Clamp Bracket Installation

LTX Panel

Cable 

Clamp 

Bracket

Summary of Contents for LTX




































Reviews:

No comments

Brands by name

Popular brands

Load more brands