background image

Telect, Inc. • USA +1.509.926.6000 • 52.33.3836.37.52
www.telect.com • © 2010 Telect, Inc., All Rights Reserved, 118677-4 A0

Page 2

Telect is not liable for shipping damage. If the product is damaged, notify the carrier and call 
Telect’s Customer Service Department at 1-800-551-4567 (domestic only) or 1-509-926-6000 for 
further recourse.

NOTE: 

For service or warranty information, please visit telect.com website, or email inquiries to 

[email protected] and click on the “Support” tab, or phone us at 800-551-4567 (domestic only) 
or 509-926-6000.

CAUTION

 

!

CAUTION!  Install this equipment in locations only accessible to qualified persons.

1.3 Specifications

Alarms:

Specification:

Alarm Relay Contacts

0.6A @ 60 Vdc

Alarm Card Power Rating

1W

Alarm Wire Size

Solid: #26 to #22 AWG

Physical*/Environment:

Specification:

Operating Temp Range

–10°C (14°F) to 55°C (131°F)

Weight With Packaging

~10 lb (~4½ kg)

Inputs/Outputs:

Specification:

Max. Breaker (each)

100A.

Max. Output Load (each)

80A continuous

Max. Total Load Rating

320A continuous

Voltage Range

+20 to +28 Vdc

–40 to –60 Vdc

BATT & RTN Wire Size

#8 to #2 AWG

Ground Wire Size

#10 to #2 AWG (depends on input fuse)

Terminal Studs (Input, Output, and Earth Ground)

M5 dual studs on 

5

/8

centers

Power Dissipation

17W per channel

Summary of Contents for 009-7000-0104











Reviews: