background image

Metrobility 10/100 AutoTwister       23

Warranty and Servicing

Telco Systems’ Product Warranty

TELCO MAKES NO WARRANTIES EXCEPT AS HEREIN SET FORTH: Telco warrants that the equipment and accessories manufactured 

by Telco, when used in the application and manner for which they are intended, will be free from defects caused by faulty material or poor 
workmanship from the date of shipment. This warranty is subject to change at any time. The warranty that applies is that which is in effect at 

the time the equipment ships. Warranty period is specific to particular product offerings. These periods are as follows:

 

Metrobility Products- 1 year
IP and EdgeGate Products – 1 year

Telco’s liability under this warranty is limited to, the obligation, at Telco’s sole option, to repair or, to replace at Telco’s plant at Massachu-

setts, any part found to be defective under normal use and service within the warranty period specified herein, provided:

a) Telco is promptly notified in writing upon discovery of such defects;

b) The defective parts are returned to Telco, transportation charges prepaid in accordance with Telco’s instructions;
c) Telco’s examination shall disclose to its satisfaction that such defects have not been caused by misuse, abuse, neglect, 

accident, or adjustments other than those specified in the Telco Operating and Maintenance Manual. Telco shall have no re

-

sponsibility under this warranty for defects, which have been caused by misuse, abuse, improper application, repair, alteration, 

accident or negligence in use, storage, transportation or handling. Further, the original identification markings must not have 

been removed, defaced or altered.
d) Equipment has been installed and operated, and maintained, in complete accordance with the Telco Operating and Mainte-
nance Manual, and good engineering practice.

Though component parts of Telco-manufactured goods are covered by the above warranty, TELCO MAKES NO WARRANTY OF MER-

CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE NOR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, FOR ANY 
EQUIPMENT OR MERCHANDISE NOT MANUFACTURED BY TELCO (FOR EXAMPLE BUT WITHOUT LIMITATION, ACCES

-

SORIES AND AUXILIARY ITEMS). 

However, Telco will cooperate reasonably with Purchaser in attempting to secure, where possible, the benefit of any warranties which the 

manufacturer of such non-Telco items may provide. All ordered replacement parts or parts replaced during the warranty period assume the 
unexpired portion of the original parts warranty or ninety (90) days from date of shipment, whichever is longer.

Replacement, Repair or Refund Procedure for Hardware: 

Telco’s sole obligation under this express warranty shall be, at Telco’s option 

and expense, to repair the defective product or part or deliver to Customer an equivalent product or part to replace the defective item. All 
products that are replaced will become the property of Telco Systems. Replacement products or parts may be new or reconditioned. Telco 
warrants any replaced or repaired product or part for ninety (90) days from shipment, or the remainder of the initial warranty period, which-
ever is longer. Telco reserves the right to refund the purchase price paid for the defective product as its exclusive warranty remedy.

To Receive a Return Materials Authorization (RMA) Number: 

Please contact the party from whom you purchased the product. If you 

purchased the product directly from Telco Systems, contact the Telco Systems Customer Care Group.

Software: 

Telco warrants to Customer that each software program licensed from it will, if operated as directed in the user documentation, 

substantially achieve the functionality described in the user documentation for a period of ninety (90) days from the date of purchase from 
Telco or its authorized reseller. No updates or upgrades are provided under this warranty. Telco’s sole obligation under this express warranty 
shall be, at Telco’s option and expense, to refund the purchase price for the software product or replace the software product with software 
which meets the requirements of this warranty as described above. Customer assumes responsibility for the selection of the appropriate 
programs and associated reference materials. Telco expressly disclaims any warranty or representation that its software products will meet 
Customer’s requirements or work in combination with any hardware or software products provided by third parties, that the operation of the 
software products will be uninterrupted or error free, or that all defects in the software products will be corrected.

The foregoing warranties are in lieu of any and all other warranties, expressed or implied, including, but not limited to, warranties of 

merchantability, fitness for a particular purpose or against infringement of any rights of third parties. Telco’s liability on any claim for money 

damages (including, without limitation negligence for any loss or damage arising out of, connected with, or resulting from the sale of products 
hereunder, or from the performance or breach thereof, or from the design, manufacture, sale, delivery, resale, installation, inspection, repair, 
operation or use of any merchandise manufactured by Telco) shall in no case exceed the price allocable to the merchandise or part thereof 
which gave rise to the claim. Purchaser will hold Telco harmless with respect to any claims or actions by third parties. In particular, Telco 
expressly disclaims and shall in no event be liable for any indirect, special, incidental or consequential damages.

Summary of Contents for Metrobility 10/100 AutoTwister 2643-13-01

























Reviews: