manualshive.com logo in svg

Tektronix KEITHLEY 2450, Quick Start Manual

Share
Download
Tektronix KEITHLEY 2450 Quick Start Manual Download Page 8

SMU Potentiostats and EC-UPGRADE Kit Quick Start Guide 

 

8 

071347302 / March 2020 

 

For three-electrode applications, the WE and WES connectors are stacked and attached to the working 

electrode. The CE and RE connectors connect to the counter electrode and reference electrode, respectively. 

Figure 8: Three-electrode cell testing cable connections 

 

For four-electrode applications, each device-side cable connector is used separately. 

Figure 9: Four-electrode cell testing cable connections 

 

 

Attach the alligator clips 

Four insulated alligator clips are supplied. You can attach these clips to the ends of the device-side connectors, 

as shown in the following graphic. The clips provide a safe, secure way to connect to your device. 

Figure 10: Alligator clip attached to accessory cable connector 

 

For small cells and electrodes, you can use commercially available banana-to-microclip connectors by plugging 

them directly into the cable connectors. 

Once the appropriate connectors or clips are attached, you are ready to connect to the test cell. 

 

Summary of Contents for KEITHLEY 2450

























Reviews:

No comments

Brands by name

Popular brands

Load more brands